Ubuntu Sverige

SMART Error Log Version: 1
ATA Error Count: 194 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.

Error 194 occurred at disk power-on lifetime: 3467 hours (144 days + 11 hours)
When the command that caused the error occurred, the device was active or idle.

After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 db a4 d1 02 Error: UNC at LBA = 0x02d1a4db = 47293659

Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 08 d5 a4 d1 e2 00 00:01:31.522 READ DMA
27 00 00 00 00 00 e0 00 00:01:31.522 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
ec 00 00 00 00 00 a0 02 00:01:31.514 IDENTIFY DEVICE
ef 03 46 00 00 00 a0 02 00:01:31.506 SET FEATURES [Set transfer mode]
27 00 00 00 00 00 e0 00 00:01:31.490 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]

Error 193 occurred at disk power-on lifetime: 3467 hours (144 days + 11 hours)
When the command that caused the error occurred, the device was active or idle.

After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 db a4 d1 02 Error: UNC at LBA = 0x02d1a4db = 47293659

Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 08 d5 a4 d1 e2 00 00:01:28.522 READ DMA
27 00 00 00 00 00 e0 00 00:01:28.522 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
ec 00 00 00 00 00 a0 02 00:01:28.514 IDENTIFY DEVICE
ef 03 46 00 00 00 a0 02 00:01:28.508 SET FEATURES [Set transfer mode]
27 00 00 00 00 00 e0 00 00:01:28.490 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]

Error 192 occurred at disk power-on lifetime: 3467 hours (144 days + 11 hours)
When the command that caused the error occurred, the device was active or idle.

After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 db a4 d1 02 Error: UNC at LBA = 0x02d1a4db = 47293659

Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 08 d5 a4 d1 e2 00 00:01:25.574 READ DMA
27 00 00 00 00 00 e0 00 00:01:25.574 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
ec 00 00 00 00 00 a0 02 00:01:25.566 IDENTIFY DEVICE
ef 03 46 00 00 00 a0 02 00:01:25.559 SET FEATURES [Set transfer mode]
27 00 00 00 00 00 e0 00 00:01:25.542 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]

Error 191 occurred at disk power-on lifetime: 3467 hours (144 days + 11 hours)
When the command that caused the error occurred, the device was active or idle.

After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 db a4 d1 02 Error: UNC at LBA = 0x02d1a4db = 47293659

Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 08 d5 a4 d1 e2 00 00:01:22.582 READ DMA
27 00 00 00 00 00 e0 00 00:01:22.582 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
ec 00 00 00 00 00 a0 02 00:01:22.573 IDENTIFY DEVICE
ef 03 46 00 00 00 a0 02 00:01:22.569 SET FEATURES [Set transfer mode]
27 00 00 00 00 00 e0 00 00:01:22.550 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]

Error 190 occurred at disk power-on lifetime: 3467 hours (144 days + 11 hours)
When the command that caused the error occurred, the device was active or idle.

After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 db a4 d1 02 Error: UNC at LBA = 0x02d1a4db = 47293659

Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 08 d5 a4 d1 e2 00 00:01:19.586 READ DMA
27 00 00 00 00 00 e0 00 00:01:19.586 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
ec 00 00 00 00 00 a0 02 00:01:19.577 IDENTIFY DEVICE
ef 03 46 00 00 00 a0 02 00:01:19.570 SET FEATURES [Set transfer mode]
27 00 00 00 00 00 e0 00 00:01:19.554 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]

erikoksanen@erikoksanen:~$ dmesg
[ 0.000000] microcode: CPU0 microcode updated early to revision 0x29, date = 2013-06-12
[ 0.000000] Initializing cgroup subsys cpuset
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Initializing cgroup subsys cpuacct
[ 0.000000] Linux version 4.4.0-22-generic (buildd@lgw01-41) (gcc version 5.3.1 20160413 (Ubuntu 5.3.1-14ubuntu2) ) #40-Ubuntu SMP Thu May 12 22:03:46 UTC 2016 (Ubuntu 4.4.0-22.40-generic 4.4.
[ 0.000000] Command line: BOOT_IMAGE=/boot/vmlinuz-4.4.0-22-generic root=UUID=b51f678b-18c8-4afe-bb6d-707f6a4f0ade ro quiet splash
[ 0.000000] KERNEL supported cpus:
[ 0.000000] Intel GenuineIntel
[ 0.000000] AMD AuthenticAMD
[ 0.000000] Centaur CentaurHauls
[ 0.000000] x86/fpu: xstate_offset[2]: 576, xstate_sizes[2]: 256
[ 0.000000] x86/fpu: Supporting XSAVE feature 0x01: 'x87 floating point registers'
[ 0.000000] x86/fpu: Supporting XSAVE feature 0x02: 'SSE registers'
[ 0.000000] x86/fpu: Supporting XSAVE feature 0x04: 'AVX registers'
[ 0.000000] x86/fpu: Enabled xstate features 0x7, context size is 832 bytes, using 'standard' format.
[ 0.000000] x86/fpu: Using 'eager' FPU context switches.
[ 0.000000] e820: BIOS-provided physical RAM map:
[ 0.000000] BIOS-e820: [mem 0x0000000000000000-0x000000000009d7ff] usable
[ 0.000000] BIOS-e820: [mem 0x000000000009d800-0x000000000009ffff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000000e0000-0x00000000000fffff] reserved
[ 0.000000] BIOS-e820: [mem 0x0000000000100000-0x00000000deb90fff] usable
[ 0.000000] BIOS-e820: [mem 0x00000000deb91000-0x00000000df140fff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000df141000-0x00000000df385fff] ACPI NVS
[ 0.000000] BIOS-e820: [mem 0x00000000df386000-0x00000000df393fff] ACPI data
[ 0.000000] BIOS-e820: [mem 0x00000000df394000-0x00000000df3c0fff] ACPI NVS
[ 0.000000] BIOS-e820: [mem 0x00000000df3c1000-0x00000000df3c5fff] ACPI data
[ 0.000000] BIOS-e820: [mem 0x00000000df3c6000-0x00000000df408fff] ACPI NVS
[ 0.000000] BIOS-e820: [mem 0x00000000df409000-0x00000000df7fffff] usable
[ 0.000000] BIOS-e820: [mem 0x00000000f8000000-0x00000000fbffffff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000fec00000-0x00000000fec00fff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000fed00000-0x00000000fed03fff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000fed1c000-0x00000000fed1ffff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000fee00000-0x00000000fee00fff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000ff000000-0x00000000ffffffff] reserved
[ 0.000000] BIOS-e820: [mem 0x0000000100000000-0x000000041effffff] usable
[ 0.000000] NX (Execute Disable) protection: active
[ 0.000000] SMBIOS 2.6 present.
[ 0.000000] DMI: System manufacturer System Product Name/P8Z68-V GEN3, BIOS 3304 04/17/2012
[ 0.000000] e820: update [mem 0x00000000-0x00000fff] usable ==> reserved
[ 0.000000] e820: remove [mem 0x000a0000-0x000fffff] usable
[ 0.000000] e820: last_pfn = 0x41f000 max_arch_pfn = 0x400000000
[ 0.000000] MTRR default type: uncachable
[ 0.000000] MTRR fixed ranges enabled:
[ 0.000000] 00000-9FFFF write-back
[ 0.000000] A0000-BFFFF uncachable
[ 0.000000] C0000-CFFFF write-protect
[ 0.000000] D0000-E7FFF uncachable
[ 0.000000] E8000-FFFFF write-protect
[ 0.000000] MTRR variable ranges enabled:
[ 0.000000] 0 base 000000000 mask C00000000 write-back
[ 0.000000] 1 base 400000000 mask FF0000000 write-back
[ 0.000000] 2 base 410000000 mask FF8000000 write-back
[ 0.000000] 3 base 418000000 mask FFC000000 write-back
[ 0.000000] 4 base 41C000000 mask FFE000000 write-back
[ 0.000000] 5 base 41E000000 mask FFF000000 write-back
[ 0.000000] 6 base 0E0000000 mask FE0000000 uncachable
[ 0.000000] 7 disabled
[ 0.000000] 8 disabled
[ 0.000000] 9 disabled
[ 0.000000] x86/PAT: Configuration [0-7]: WB WC UC- UC WB WC UC- WT
[ 0.000000] original variable MTRRs
[ 0.000000] reg 0, base: 0GB, range: 16GB, type WB
[ 0.000000] reg 1, base: 16GB, range: 256MB, type WB
[ 0.000000] reg 2, base: 16640MB, range: 128MB, type WB
[ 0.000000] reg 3, base: 16768MB, range: 64MB, type WB
[ 0.000000] reg 4, base: 16832MB, range: 32MB, type WB
[ 0.000000] reg 5, base: 16864MB, range: 16MB, type WB
[ 0.000000] reg 6, base: 3584MB, range: 512MB, type UC
[ 0.000000] total RAM covered: 16368M
[ 0.000000] Found optimal setting for mtrr clean up
[ 0.000000] gran_size: 64K chunk_size: 32M num_reg: 7 lose cover RAM: 0G
[ 0.000000] New variable MTRRs
[ 0.000000] reg 0, base: 0GB, range: 2GB, type WB
[ 0.000000] reg 1, base: 2GB, range: 1GB, type WB
[ 0.000000] reg 2, base: 3GB, range: 512MB, type WB
[ 0.000000] reg 3, base: 4GB, range: 4GB, type WB
[ 0.000000] reg 4, base: 8GB, range: 8GB, type WB
[ 0.000000] reg 5, base: 16GB, range: 512MB, type WB
[ 0.000000] reg 6, base: 16880MB, range: 16MB, type UC
[ 0.000000] e820: update [mem 0xe0000000-0xffffffff] usable ==> reserved
[ 0.000000] e820: last_pfn = 0xdf800 max_arch_pfn = 0x400000000
[ 0.000000] found SMP MP-table at [mem 0x000fcda0-0x000fcdaf] mapped at [ffff8800000fcda0]
[ 0.000000] Scanning 1 areas for low memory corruption
[ 0.000000] Base memory trampoline at [ffff880000097000] 97000 size 24576
[ 0.000000] BRK [0x021ff000, 0x021fffff] PGTABLE
[ 0.000000] BRK [0x02200000, 0x02200fff] PGTABLE
[ 0.000000] BRK [0x02201000, 0x02201fff] PGTABLE
[ 0.000000] BRK [0x02202000, 0x02202fff] PGTABLE
[ 0.000000] BRK [0x02203000, 0x02203fff] PGTABLE
[ 0.000000] BRK [0x02204000, 0x02204fff] PGTABLE
[ 0.000000] RAMDISK: [mem 0x33c24000-0x35e09fff]
[ 0.000000] ACPI: Early table checksum verification disabled
[ 0.000000] ACPI: RSDP 0x00000000000F0450 000024 (v02 ALASKA)
[ 0.000000] ACPI: XSDT 0x00000000DF386070 000064 (v01 ALASKA A M I 01072009 AMI 00010013)
[ 0.000000] ACPI: FACP 0x00000000DF391C00 0000F4 (v04 ALASKA A M I 01072009 AMI 00010013)
[ 0.000000] ACPI: DSDT 0x00000000DF386168 00BA92 (v02 ALASKA A M I 00000015 INTL 20051117)
[ 0.000000] ACPI: FACS 0x00000000DF3BFF80 000040
[ 0.000000] ACPI: APIC 0x00000000DF391CF8 000092 (v03 ALASKA A M I 01072009 AMI 00010013)
[ 0.000000] ACPI: MCFG 0x00000000DF391D90 00003C (v01 ALASKA A M I 01072009 MSFT 00000097)
[ 0.000000] ACPI: HPET 0x00000000DF391DD0 000038 (v01 ALASKA A M I 01072009 AMI. 00000005)
[ 0.000000] ACPI: SSDT 0x00000000DF391E08 00036D (v01 SataRe SataTabl 00001000 INTL 20091112)
[ 0.000000] ACPI: SSDT 0x00000000DF392178 0009AA (v01 PmRef Cpu0Ist 00003000 INTL 20051117)
[ 0.000000] ACPI: SSDT 0x00000000DF392B28 000A92 (v01 PmRef CpuPm 00003000 INTL 20051117)
[ 0.000000] ACPI: DMAR 0x00000000DF3935C0 000078 (v01 INTEL SNB 00000001 INTL 00000001)
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] No NUMA configuration found
[ 0.000000] Faking a node at [mem 0x0000000000000000-0x000000041effffff]
[ 0.000000] NODE_DATA(0) allocated [mem 0x41efec000-0x41eff0fff]
[ 0.000000] Zone ranges:
[ 0.000000] DMA [mem 0x0000000000001000-0x0000000000ffffff]
[ 0.000000] DMA32 [mem 0x0000000001000000-0x00000000ffffffff]
[ 0.000000] Normal [mem 0x0000000100000000-0x000000041effffff]
[ 0.000000] Device empty
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000000001000-0x000000000009cfff]
[ 0.000000] node 0: [mem 0x0000000000100000-0x00000000deb90fff]
[ 0.000000] node 0: [mem 0x00000000df409000-0x00000000df7fffff]
[ 0.000000] node 0: [mem 0x0000000100000000-0x000000041effffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000000001000-0x000000041effffff]
[ 0.000000] On node 0 totalpages: 4185892
[ 0.000000] DMA zone: 64 pages used for memmap
[ 0.000000] DMA zone: 21 pages reserved
[ 0.000000] DMA zone: 3996 pages, LIFO batch:0
[ 0.000000] DMA32 zone: 14207 pages used for memmap
[ 0.000000] DMA32 zone: 909192 pages, LIFO batch:31
[ 0.000000] Normal zone: 51136 pages used for memmap
[ 0.000000] Normal zone: 3272704 pages, LIFO batch:31
[ 0.000000] ACPI: PM-Timer IO Port: 0x408
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0xff] high edge lint[0x1])
[ 0.000000] IOAPIC[0]: apic_id 2, version 32, address 0xfec00000, GSI 0-23
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[ 0.000000] ACPI: IRQ0 used by override.
[ 0.000000] ACPI: IRQ9 used by override.
[ 0.000000] Using ACPI (MADT) for SMP configuration information
[ 0.000000] ACPI: HPET id: 0x8086a701 base: 0xfed00000
[ 0.000000] smpboot: Allowing 8 CPUs, 0 hotplug CPUs
[ 0.000000] PM: Registered nosave memory: [mem 0x00000000-0x00000fff]
[ 0.000000] PM: Registered nosave memory: [mem 0x0009d000-0x0009dfff]
[ 0.000000] PM: Registered nosave memory: [mem 0x0009e000-0x0009ffff]
[ 0.000000] PM: Registered nosave memory: [mem 0x000a0000-0x000dffff]
[ 0.000000] PM: Registered nosave memory: [mem 0x000e0000-0x000fffff]
[ 0.000000] PM: Registered nosave memory: [mem 0xdeb91000-0xdf140fff]
[ 0.000000] PM: Registered nosave memory: [mem 0xdf141000-0xdf385fff]
[ 0.000000] PM: Registered nosave memory: [mem 0xdf386000-0xdf393fff]
[ 0.000000] PM: Registered nosave memory: [mem 0xdf394000-0xdf3c0fff]
[ 0.000000] PM: Registered nosave memory: [mem 0xdf3c1000-0xdf3c5fff]
[ 0.000000] PM: Registered nosave memory: [mem 0xdf3c6000-0xdf408fff]
[ 0.000000] PM: Registered nosave memory: [mem 0xdf800000-0xf7ffffff]
[ 0.000000] PM: Registered nosave memory: [mem 0xf8000000-0xfbffffff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfc000000-0xfebfffff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfec00000-0xfec00fff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfec01000-0xfecfffff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfed00000-0xfed03fff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfed04000-0xfed1bfff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfed1c000-0xfed1ffff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfed20000-0xfedfffff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfee00000-0xfee00fff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfee01000-0xfeffffff]
[ 0.000000] PM: Registered nosave memory: [mem 0xff000000-0xffffffff]
[ 0.000000] e820: [mem 0xdf800000-0xf7ffffff] available for PCI devices
[ 0.000000] Booting paravirtualized kernel on bare hardware
[ 0.000000] clocksource: refined-jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645519600211568 ns
[ 0.000000] setup_percpu: NR_CPUS:256 nr_cpumask_bits:256 nr_cpu_ids:8 nr_node_ids:1
[ 0.000000] PERCPU: Embedded 33 pages/cpu @ffff88041ec00000 s98008 r8192 d28968 u262144
[ 0.000000] pcpu-alloc: s98008 r8192 d28968 u262144 alloc=1*2097152
[ 0.000000] pcpu-alloc: [0] 0 1 2 3 4 5 6 7
[ 0.000000] Built 1 zonelists in Node order, mobility grouping on. Total pages: 4120464
[ 0.000000] Policy zone: Normal
[ 0.000000] Kernel command line: BOOT_IMAGE=/boot/vmlinuz-4.4.0-22-generic root=UUID=b51f678b-18c8-4afe-bb6d-707f6a4f0ade ro quiet splash
[ 0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.000000] Calgary: detecting Calgary via BIOS EBDA area
[ 0.000000] Calgary: Unable to locate Rio Grande table in EBDA - bailing!
[ 0.000000] Memory: 16360736K/16743568K available (8359K kernel code, 1278K rwdata, 3920K rodata, 1480K init, 1292K bss, 382832K reserved, 0K cma-reserved)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=8, Nodes=1
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] Build-time adjustment of leaf fanout to 64.
[ 0.000000] RCU restricting CPUs from NR_CPUS=256 to nr_cpu_ids=8.
[ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=64, nr_cpu_ids=8
[ 0.000000] NR_IRQS:16640 nr_irqs:488 16
[ 0.000000] Console: colour VGA+ 80x25
[ 0.000000] console [tty0] enabled
[ 0.000000] clocksource: hpet: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 133484882848 ns
[ 0.000000] hpet clockevent registered
[ 0.000000] tsc: Fast TSC calibration using PIT
[ 0.000000] tsc: Detected 3411.248 MHz processor
[ 0.000025] Calibrating delay loop (skipped), value calculated using timer frequency.. 6822.49 BogoMIPS (lpj=13644992)
[ 0.000026] pid_max: default: 32768 minimum: 301
[ 0.000030] ACPI: Core revision 20150930
[ 0.005512] ACPI: 4 ACPI AML tables successfully acquired and loaded
[ 0.005529] Security Framework initialized
[ 0.005530] Yama: becoming mindful.
[ 0.005541] AppArmor: AppArmor initialized
[ 0.006242] Dentry cache hash table entries: 2097152 (order: 12, 16777216 bytes)
[ 0.008515] Inode-cache hash table entries: 1048576 (order: 11, 8388608 bytes)
[ 0.009514] Mount-cache hash table entries: 32768 (order: 6, 262144 bytes)
[ 0.009527] Mountpoint-cache hash table entries: 32768 (order: 6, 262144 bytes)
[ 0.009704] Initializing cgroup subsys io
[ 0.009707] Initializing cgroup subsys memory
[ 0.009711] Initializing cgroup subsys devices
[ 0.009713] Initializing cgroup subsys freezer
[ 0.009714] Initializing cgroup subsys net_cls
[ 0.009716] Initializing cgroup subsys perf_event
[ 0.009717] Initializing cgroup subsys net_prio
[ 0.009719] Initializing cgroup subsys hugetlb
[ 0.009721] Initializing cgroup subsys pids
[ 0.009736] CPU: Physical Processor ID: 0
[ 0.009737] CPU: Processor Core ID: 0
[ 0.009740] ENERGY_PERF_BIAS: Set to 'normal', was 'performance'
[ 0.009741] ENERGY_PERF_BIAS: View and update with x86_energy_perf_policy(8)
[ 0.009743] mce: CPU supports 9 MCE banks
[ 0.009752] CPU0: Thermal monitoring enabled (TM1)
[ 0.009758] process: using mwait in idle threads
[ 0.009760] Last level iTLB entries: 4KB 512, 2MB 8, 4MB 8
[ 0.009761] Last level dTLB entries: 4KB 512, 2MB 32, 4MB 32, 1GB 0
[ 0.010061] Freeing SMP alternatives memory: 28K (ffffffff820b3000 - ffffffff820ba000)
[ 0.222917] ftrace: allocating 31906 entries in 125 pages
[ 0.234218] smpboot: Max logical packages: 2
[ 0.234220] smpboot: APIC(0) Converting physical 0 to logical package 0
[ 0.234224] DMAR: Host address width 36
[ 0.234225] DMAR: DRHD base: 0x000000fed90000 flags: 0x1
[ 0.234231] DMAR: dmar0: reg_base_addr fed90000 ver 1:0 cap c9008020660262 ecap f0105a
[ 0.234232] DMAR: RMRR base: 0x000000df0d6000 end: 0x000000df0e4fff
[ 0.234233] DMAR-IR: IOAPIC id 2 under DRHD base 0xfed90000 IOMMU 0
[ 0.234234] DMAR-IR: HPET id 0 under DRHD base 0xfed90000
[ 0.234235] DMAR-IR: Queued invalidation will be enabled to support x2apic and Intr-remapping.
[ 0.234404] DMAR-IR: Enabled IRQ remapping in x2apic mode
[ 0.234405] x2apic enabled
[ 0.234410] Switched APIC routing to cluster x2apic.
[ 0.234827] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
[ 0.274514] TSC deadline timer enabled
[ 0.274516] smpboot: CPU0: Intel(R) Core(TM) i7-2600 CPU @ 3.40GHz (family: 0x6, model: 0x2a, stepping: 0x7)
[ 0.274528] Performance Events: PEBS fmt1+, 16-deep LBR, SandyBridge events, full-width counters, Intel PMU driver.
[ 0.274543] ... version: 3
[ 0.274544] ... bit width: 48
[ 0.274545] ... generic registers: 4
[ 0.274546] ... value mask: 0000ffffffffffff
[ 0.274546] ... max period: 0000ffffffffffff
[ 0.274547] ... fixed-purpose events: 3
[ 0.274548] ... event mask: 000000070000000f
[ 0.275113] x86: Booting SMP configuration:
[ 0.275115] .... node #0, CPUs: #1
[ 0.275726] microcode: CPU1 microcode updated early to revision 0x29, date = 2013-06-12
[ 0.277874] NMI watchdog: enabled on all CPUs, permanently consumes one hw-PMU counter.
[ 0.277934] #2
[ 0.278481] microcode: CPU2 microcode updated early to revision 0x29, date = 2013-06-12
[ 0.280606] #3
[ 0.281128] microcode: CPU3 microcode updated early to revision 0x29, date = 2013-06-12
[ 0.283250] #4 #5 #6 #7
[ 0.292805] x86: Booted up 1 node, 8 CPUs
[ 0.292807] smpboot: Total of 8 processors activated (54579.96 BogoMIPS)
[ 0.299165] devtmpfs: initialized
[ 0.301628] evm: security.selinux
[ 0.301630] evm: security.SMACK64
[ 0.301630] evm: security.SMACK64EXEC
[ 0.301631] evm: security.SMACK64TRANSMUTE
[ 0.301632] evm: security.SMACK64MMAP
[ 0.301632] evm: security.ima
[ 0.301633] evm: security.capability
[ 0.301680] PM: Registering ACPI NVS region [mem 0xdf141000-0xdf385fff] (2379776 bytes)
[ 0.301701] PM: Registering ACPI NVS region [mem 0xdf394000-0xdf3c0fff] (184320 bytes)
[ 0.301703] PM: Registering ACPI NVS region [mem 0xdf3c6000-0xdf408fff] (274432 bytes)
[ 0.301767] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
[ 0.301826] pinctrl core: initialized pinctrl subsystem
[ 0.301914] RTC time: 4:08:59, date: 05/27/16
[ 0.301996] NET: Registered protocol family 16
[ 0.311019] cpuidle: using governor ladder
[ 0.323013] cpuidle: using governor menu
[ 0.323019] PCCT header not found.
[ 0.323124] ACPI FADT declares the system doesn't support PCIe ASPM, so disable it
[ 0.323126] ACPI: bus type PCI registered
[ 0.323127] acpiphp: ACPI Hot Plug PCI Controller Driver version: 0.5
[ 0.323190] PCI: MMCONFIG for domain 0000 [bus 00-3f] at [mem 0xf8000000-0xfbffffff] (base 0xf8000000)
[ 0.323192] PCI: MMCONFIG at [mem 0xf8000000-0xfbffffff] reserved in E820
[ 0.323199] PCI: Using configuration type 1 for base access
[ 0.323225] core: PMU erratum BJ122, BV98, HSD29 worked around, HT is on
[ 0.339334] ACPI: Added _OSI(Module Device)
[ 0.339336] ACPI: Added _OSI(Processor Device)
[ 0.339337] ACPI: Added _OSI(3.0 _SCP Extensions)
[ 0.339338] ACPI: Added _OSI(Processor Aggregator Device)
[ 0.341264] ACPI: Executed 1 blocks of module-level executable AML code
[ 0.343269] ACPI: Dynamic OEM Table Load:
[ 0.343275] ACPI: SSDT 0xFFFF88040BC26000 00083B (v01 PmRef Cpu0Cst 00003001 INTL 20051117)
[ 0.343652] ACPI: Dynamic OEM Table Load:
[ 0.343655] ACPI: SSDT 0xFFFF88040BD79C00 000303 (v01 PmRef ApIst 00003000 INTL 20051117)
[ 0.343980] ACPI: Dynamic OEM Table Load:
[ 0.343982] ACPI: SSDT 0xFFFF88040BD71A00 000119 (v01 PmRef ApCst 00003000 INTL 20051117)
[ 0.345005] ACPI : EC: EC started
[ 0.345010] ACPI: Interpreter enabled
[ 0.345017] ACPI Exception: AE_NOT_FOUND, While evaluating Sleep State [\_S2_] (20150930/hwxface-580)
[ 0.345027] ACPI: (supports S0 S1 S3 S4 S5)
[ 0.345028] ACPI: Using IOAPIC for interrupt routing
[ 0.345047] PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug
[ 0.349687] ACPI: Power Resource [FN00] (off)
[ 0.349747] ACPI: Power Resource [FN01] (off)
[ 0.349803] ACPI: Power Resource [FN02] (off)
[ 0.349861] ACPI: Power Resource [FN03] (off)
[ 0.349917] ACPI: Power Resource [FN04] (off)
[ 0.350327] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-3e])
[ 0.350332] acpi PNP0A08:00: _OSC: OS supports [ExtendedConfig ASPM ClockPM Segments MSI]
[ 0.350377] \_SB_.PCI0:_OSC invalid UUID
[ 0.350378] _OSC request data:1 1f 0
[ 0.350381] acpi PNP0A08:00: _OSC failed (AE_ERROR); disabling ASPM
[ 0.350691] PCI host bridge to bus 0000:00
[ 0.350694] pci_bus 0000:00: root bus resource [io 0x0000-0x0cf7 window]
[ 0.350695] pci_bus 0000:00: root bus resource [io 0x0d00-0xffff window]
[ 0.350696] pci_bus 0000:00: root bus resource [mem 0x000a0000-0x000bffff window]
[ 0.350697] pci_bus 0000:00: root bus resource [mem 0x000d0000-0x000d3fff window]
[ 0.350698] pci_bus 0000:00: root bus resource [mem 0x000d4000-0x000d7fff window]
[ 0.350700] pci_bus 0000:00: root bus resource [mem 0x000d8000-0x000dbfff window]
[ 0.350701] pci_bus 0000:00: root bus resource [mem 0x000dc000-0x000dffff window]
[ 0.350702] pci_bus 0000:00: root bus resource [mem 0x000e0000-0x000e3fff window]
[ 0.350703] pci_bus 0000:00: root bus resource [mem 0x000e4000-0x000e7fff window]
[ 0.350704] pci_bus 0000:00: root bus resource [mem 0xe0000000-0xfeafffff window]
[ 0.350705] pci_bus 0000:00: root bus resource [bus 00-3e]
[ 0.350711] pci 0000:00:00.0: [8086:0100] type 00 class 0x060000
[ 0.350782] pci 0000:00:01.0: [8086:0101] type 01 class 0x060400
[ 0.350805] pci 0000:00:01.0: PME# supported from D0 D3hot D3cold
[ 0.350838] pci 0000:00:01.0: System wakeup disabled by ACPI
[ 0.350890] pci 0000:00:16.0: [8086:1c3a] type 00 class 0x078000
[ 0.350921] pci 0000:00:16.0: reg 0x10: [mem 0xf742c000-0xf742c00f 64bit]
[ 0.350979] pci 0000:00:16.0: PME# supported from D0 D3hot D3cold
[ 0.351049] pci 0000:00:19.0: [8086:1503] type 00 class 0x020000
[ 0.351073] pci 0000:00:19.0: reg 0x10: [mem 0xf7400000-0xf741ffff]
[ 0.351081] pci 0000:00:19.0: reg 0x14: [mem 0xf7429000-0xf7429fff]
[ 0.351088] pci 0000:00:19.0: reg 0x18: [io 0xf040-0xf05f]
[ 0.351135] pci 0000:00:19.0: PME# supported from D0 D3hot D3cold
[ 0.351170] pci 0000:00:19.0: System wakeup disabled by ACPI
[ 0.351201] pci 0000:00:1a.0: [8086:1c2d] type 00 class 0x0c0320
[ 0.351227] pci 0000:00:1a.0: reg 0x10: [mem 0xf7428000-0xf74283ff]
[ 0.351295] pci 0000:00:1a.0: PME# supported from D0 D3hot D3cold
[ 0.351341] pci 0000:00:1a.0: System wakeup disabled by ACPI
[ 0.351373] pci 0000:00:1b.0: [8086:1c20] type 00 class 0x040300
[ 0.351397] pci 0000:00:1b.0: reg 0x10: [mem 0xf7420000-0xf7423fff 64bit]
[ 0.351454] pci 0000:00:1b.0: PME# supported from D0 D3hot D3cold
[ 0.351494] pci 0000:00:1b.0: System wakeup disabled by ACPI
[ 0.351524] pci 0000:00:1c.0: [8086:1c10] type 01 class 0x060400
[ 0.351594] pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold
[ 0.351634] pci 0000:00:1c.0: System wakeup disabled by ACPI
[ 0.351663] pci 0000:00:1c.1: [8086:1c12] type 01 class 0x060400
[ 0.351733] pci 0000:00:1c.1: PME# supported from D0 D3hot D3cold
[ 0.351772] pci 0000:00:1c.1: System wakeup disabled by ACPI
[ 0.351801] pci 0000:00:1c.3: [8086:1c16] type 01 class 0x060400
[ 0.351871] pci 0000:00:1c.3: PME# supported from D0 D3hot D3cold
[ 0.351910] pci 0000:00:1c.3: System wakeup disabled by ACPI
[ 0.351940] pci 0000:00:1c.4: [8086:1c18] type 01 class 0x060400
[ 0.352010] pci 0000:00:1c.4: PME# supported from D0 D3hot D3cold
[ 0.352050] pci 0000:00:1c.4: System wakeup disabled by ACPI
[ 0.352081] pci 0000:00:1c.6: [8086:244e] type 01 class 0x060401
[ 0.352151] pci 0000:00:1c.6: PME# supported from D0 D3hot D3cold
[ 0.352190] pci 0000:00:1c.6: System wakeup disabled by ACPI
[ 0.352221] pci 0000:00:1d.0: [8086:1c26] type 00 class 0x0c0320
[ 0.352247] pci 0000:00:1d.0: reg 0x10: [mem 0xf7427000-0xf74273ff]
[ 0.352315] pci 0000:00:1d.0: PME# supported from D0 D3hot D3cold
[ 0.352380] pci 0000:00:1f.0: [8086:1c44] type 00 class 0x060100
[ 0.352532] pci 0000:00:1f.2: [8086:1c02] type 00 class 0x010601
[ 0.352553] pci 0000:00:1f.2: reg 0x10: [io 0xf090-0xf097]
[ 0.352560] pci 0000:00:1f.2: reg 0x14: [io 0xf080-0xf083]
[ 0.352567] pci 0000:00:1f.2: reg 0x18: [io 0xf070-0xf077]
[ 0.352577] pci 0000:00:1f.2: reg 0x1c: [io 0xf060-0xf063]
[ 0.352584] pci 0000:00:1f.2: reg 0x20: [io 0xf020-0xf03f]
[ 0.352591] pci 0000:00:1f.2: reg 0x24: [mem 0xf7426000-0xf74267ff]
[ 0.352620] pci 0000:00:1f.2: PME# supported from D3hot
[ 0.352679] pci 0000:00:1f.3: [8086:1c22] type 00 class 0x0c0500
[ 0.352694] pci 0000:00:1f.3: reg 0x10: [mem 0xf7425000-0xf74250ff 64bit]
[ 0.352713] pci 0000:00:1f.3: reg 0x20: [io 0xf000-0xf01f]
[ 0.352811] pci 0000:01:00.0: [10de:0a65] type 00 class 0x030000
[ 0.352827] pci 0000:01:00.0: reg 0x10: [mem 0xf6000000-0xf6ffffff]
[ 0.352835] pci 0000:01:00.0: reg 0x14: [mem 0xe0000000-0xefffffff 64bit pref]
[ 0.352843] pci 0000:01:00.0: reg 0x1c: [mem 0xf0000000-0xf1ffffff 64bit pref]
[ 0.352848] pci 0000:01:00.0: reg 0x24: [io 0xe000-0xe07f]
[ 0.352854] pci 0000:01:00.0: reg 0x30: [mem 0xf7000000-0xf707ffff pref]
[ 0.352911] pci 0000:01:00.1: [10de:0be3] type 00 class 0x040300
[ 0.352926] pci 0000:01:00.1: reg 0x10: [mem 0xf7080000-0xf7083fff]
[ 0.360598] pci 0000:00:01.0: PCI bridge to [bus 01]
[ 0.360602] pci 0000:00:01.0: bridge window [io 0xe000-0xefff]
[ 0.360606] pci 0000:00:01.0: bridge window [mem 0xf6000000-0xf70fffff]
[ 0.360610] pci 0000:00:01.0: bridge window [mem 0xe0000000-0xf1ffffff 64bit pref]
[ 0.360687] pci 0000:00:1c.0: PCI bridge to [bus 02]
[ 0.360760] pci 0000:03:00.0: [1b21:1042] type 00 class 0x0c0330
[ 0.360812] pci 0000:03:00.0: reg 0x10: [mem 0xf7300000-0xf7307fff 64bit]
[ 0.360943] pci 0000:03:00.0: PME# supported from D3hot D3cold
[ 0.360972] pci 0000:03:00.0: System wakeup disabled by ACPI
[ 0.368604] pci 0000:00:1c.1: PCI bridge to [bus 03]

0.368613] pci 0000:00:1c.1: bridge window [mem 0xf7300000-0xf73fffff]
[ 0.368722] pci 0000:04:00.0: [197b:2362] type 00 class 0x010185
[ 0.368775] pci 0000:04:00.0: reg 0x10: [io 0xd040-0xd047]
[ 0.368790] pci 0000:04:00.0: reg 0x14: [io 0xd030-0xd033]
[ 0.368806] pci 0000:04:00.0: reg 0x18: [io 0xd020-0xd027]
[ 0.368822] pci 0000:04:00.0: reg 0x1c: [io 0xd010-0xd013]
[ 0.368837] pci 0000:04:00.0: reg 0x20: [io 0xd000-0xd00f]
[ 0.368853] pci 0000:04:00.0: reg 0x24: [mem 0xf7210000-0xf72101ff]
[ 0.368869] pci 0000:04:00.0: reg 0x30: [mem 0x00000000-0x0000ffff pref]
[ 0.368918] pci 0000:04:00.0: PME# supported from D3hot
[ 0.368947] pci 0000:04:00.0: System wakeup disabled by ACPI
[ 0.376608] pci 0000:00:1c.3: PCI bridge to [bus 04]
[ 0.376614] pci 0000:00:1c.3: bridge window [io 0xd000-0xdfff]
[ 0.376619] pci 0000:00:1c.3: bridge window [mem 0xf7200000-0xf72fffff]
[ 0.376718] pci 0000:05:00.0: [1b21:1042] type 00 class 0x0c0330
[ 0.376769] pci 0000:05:00.0: reg 0x10: [mem 0xf7100000-0xf7107fff 64bit]
[ 0.376899] pci 0000:05:00.0: PME# supported from D3hot D3cold
[ 0.376927] pci 0000:05:00.0: System wakeup disabled by ACPI
[ 0.384611] pci 0000:00:1c.4: PCI bridge to [bus 05]
[ 0.384619] pci 0000:00:1c.4: bridge window [mem 0xf7100000-0xf71fffff]
[ 0.384711] pci 0000:06:00.0: [1b21:1080] type 01 class 0x060401
[ 0.384823] pci 0000:06:00.0: System wakeup disabled by ACPI
[ 0.384847] pci 0000:00:1c.6: PCI bridge to [bus 06-07] (subtractive decode)
[ 0.384856] pci 0000:00:1c.6: bridge window [io 0x0000-0x0cf7 window] (subtractive decode)
[ 0.384858] pci 0000:00:1c.6: bridge window [io 0x0d00-0xffff window] (subtractive decode)
[ 0.384859] pci 0000:00:1c.6: bridge window [mem 0x000a0000-0x000bffff window] (subtractive decode)
[ 0.384860] pci 0000:00:1c.6: bridge window [mem 0x000d0000-0x000d3fff window] (subtractive decode)
[ 0.384861] pci 0000:00:1c.6: bridge window [mem 0x000d4000-0x000d7fff window] (subtractive decode)
[ 0.384862] pci 0000:00:1c.6: bridge window [mem 0x000d8000-0x000dbfff window] (subtractive decode)
[ 0.384864] pci 0000:00:1c.6: bridge window [mem 0x000dc000-0x000dffff window] (subtractive decode)
[ 0.384865] pci 0000:00:1c.6: bridge window [mem 0x000e0000-0x000e3fff window] (subtractive decode)
[ 0.384866] pci 0000:00:1c.6: bridge window [mem 0x000e4000-0x000e7fff window] (subtractive decode)
[ 0.384867] pci 0000:00:1c.6: bridge window [mem 0xe0000000-0xfeafffff window] (subtractive decode)
[ 0.384974] pci 0000:06:00.0: PCI bridge to [bus 07] (subtractive decode)
[ 0.384995] pci 0000:06:00.0: bridge window [io 0x0000-0x0cf7 window] (subtractive decode)
[ 0.384996] pci 0000:06:00.0: bridge window [io 0x0d00-0xffff window] (subtractive decode)
[ 0.384998] pci 0000:06:00.0: bridge window [mem 0x000a0000-0x000bffff window] (subtractive decode)
[ 0.384999] pci 0000:06:00.0: bridge window [mem 0x000d0000-0x000d3fff window] (subtractive decode)
[ 0.385000] pci 0000:06:00.0: bridge window [mem 0x000d4000-0x000d7fff window] (subtractive decode)
[ 0.385001] pci 0000:06:00.0: bridge window [mem 0x000d8000-0x000dbfff window] (subtractive decode)
[ 0.385002] pci 0000:06:00.0: bridge window [mem 0x000dc000-0x000dffff window] (subtractive decode)
[ 0.385003] pci 0000:06:00.0: bridge window [mem 0x000e0000-0x000e3fff window] (subtractive decode)
[ 0.385004] pci 0000:06:00.0: bridge window [mem 0x000e4000-0x000e7fff window] (subtractive decode)
[ 0.385006] pci 0000:06:00.0: bridge window [mem 0xe0000000-0xfeafffff window] (subtractive decode)
[ 0.385372] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 10 *11 12 14 15)
[ 0.385410] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 *10 11 12 14 15)
[ 0.385446] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 10 *11 12 14 15)
[ 0.385483] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 *5 6 10 11 12 14 15)
[ 0.385518] ACPI: PCI Interrupt Link [LNKE] (IRQs *3 4 5 6 10 11 12 14 15)
[ 0.385554] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 10 11 12 14 15) *0, disabled.
[ 0.385590] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 *4 5 6 10 11 12 14 15)
[ 0.385626] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 *10 11 12 14 15)
[ 0.385803] ACPI: Enabled 4 GPEs in block 00 to 3F
[ 0.385818] ACPI : EC: GPE = 0x18, I/O: command/status = 0x66, data = 0x62
[ 0.385899] vgaarb: setting as boot device: PCI:0000:01:00.0
[ 0.385901] vgaarb: device added: PCI:0000:01:00.0,decodes=io+mem,owns=io+mem,locks=none
[ 0.385902] vgaarb: loaded
[ 0.385903] vgaarb: bridge control possible 0000:01:00.0
[ 0.386075] SCSI subsystem initialized
[ 0.386101] libata version 3.00 loaded.
[ 0.386120] ACPI: bus type USB registered
[ 0.386131] usbcore: registered new interface driver usbfs
[ 0.386137] usbcore: registered new interface driver hub
[ 0.386152] usbcore: registered new device driver usb
[ 0.386245] PCI: Using ACPI for IRQ routing
[ 0.387588] PCI: pci_cache_line_size set to 64 bytes
[ 0.387643] e820: reserve RAM buffer [mem 0x0009d800-0x0009ffff]
[ 0.387644] e820: reserve RAM buffer [mem 0xdeb91000-0xdfffffff]
[ 0.387645] e820: reserve RAM buffer [mem 0xdf800000-0xdfffffff]
[ 0.387646] e820: reserve RAM buffer [mem 0x41f000000-0x41fffffff]
[ 0.387725] NetLabel: Initializing
[ 0.387726] NetLabel: domain hash size = 128
[ 0.387727] NetLabel: protocols = UNLABELED CIPSOv4
[ 0.387737] NetLabel: unlabeled traffic allowed by default
[ 0.387785] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0, 0, 0, 0, 0, 0
[ 0.387789] hpet0: 8 comparators, 64-bit 14.318180 MHz counter
[ 0.389810] clocksource: Switched to clocksource hpet
[ 0.394047] AppArmor: AppArmor Filesystem Enabled
[ 0.394096] pnp: PnP ACPI init
[ 0.394164] system 00:00: [mem 0xfed40000-0xfed44fff] has been reserved
[ 0.394168] system 00:00: Plug and Play ACPI device, IDs PNP0c01 (active)
[ 0.394226] system 00:01: [io 0x0680-0x069f] has been reserved
[ 0.394227] system 00:01: [io 0x0200-0x020f] has been reserved
[ 0.394228] system 00:01: [io 0xffff] has been reserved
[ 0.394230] system 00:01: [io 0xffff] has been reserved
[ 0.394231] system 00:01: [io 0x0400-0x0453] could not be reserved
[ 0.394232] system 00:01: [io 0x0458-0x047f] has been reserved
[ 0.394234] system 00:01: [io 0x0500-0x057f] has been reserved
[ 0.394235] system 00:01: [io 0x164e-0x164f] has been reserved
[ 0.394237] system 00:01: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.394255] pnp 00:02: Plug and Play ACPI device, IDs PNP0b00 (active)
[ 0.394290] system 00:03: [io 0x0454-0x0457] has been reserved
[ 0.394292] system 00:03: Plug and Play ACPI device, IDs INT3f0d PNP0c02 (active)
[ 0.394352] system 00:04: [io 0x0290-0x029f] has been reserved
[ 0.394354] system 00:04: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.394389] system 00:05: [io 0x04d0-0x04d1] has been reserved
[ 0.394391] system 00:05: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.394575] system 00:06: [mem 0xfed1c000-0xfed1ffff] has been reserved
[ 0.394577] system 00:06: [mem 0xfed10000-0xfed17fff] has been reserved
[ 0.394578] system 00:06: [mem 0xfed18000-0xfed18fff] has been reserved
[ 0.394579] system 00:06: [mem 0xfed19000-0xfed19fff] has been reserved
[ 0.394580] system 00:06: [mem 0xf8000000-0xfbffffff] has been reserved
[ 0.394582] system 00:06: [mem 0xfed20000-0xfed3ffff] has been reserved
[ 0.394583] system 00:06: [mem 0xfed90000-0xfed93fff] could not be reserved
[ 0.394584] system 00:06: [mem 0xfed45000-0xfed8ffff] has been reserved
[ 0.394586] system 00:06: [mem 0xff000000-0xffffffff] has been reserved
[ 0.394587] system 00:06: [mem 0xfee00000-0xfeefffff] could not be reserved
[ 0.394588] system 00:06: [mem 0xf2000000-0xf2000fff] has been reserved
[ 0.394590] system 00:06: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.394676] pnp: PnP ACPI: found 7 devices
[ 0.400557] clocksource: acpi_pm: mask: 0xffffff max_cycles: 0xffffff, max_idle_ns: 2085701024 ns
[ 0.400575] pci 0000:00:1c.0: bridge window [io 0x1000-0x0fff] to [bus 02] add_size 1000
[ 0.400577] pci 0000:00:1c.0: bridge window [mem 0x00100000-0x000fffff 64bit pref] to [bus 02] add_size 200000 add_align 100000
[ 0.400579] pci 0000:00:1c.0: bridge window [mem 0x00100000-0x000fffff] to [bus 02] add_size 200000 add_align 100000
[ 0.400619] pci 0000:00:1c.0: res[14]=[mem 0x00100000-0x000fffff] res_to_dev_res add_size 200000 min_align 100000
[ 0.400620] pci 0000:00:1c.0: res[14]=[mem 0x00100000-0x002fffff] res_to_dev_res add_size 200000 min_align 100000
[ 0.400622] pci 0000:00:1c.0: res[15]=[mem 0x00100000-0x000fffff 64bit pref] res_to_dev_res add_size 200000 min_align 100000
[ 0.400623] pci 0000:00:1c.0: res[15]=[mem 0x00100000-0x002fffff 64bit pref] res_to_dev_res add_size 200000 min_align 100000
[ 0.400625] pci 0000:00:1c.0: res[13]=[io 0x1000-0x0fff] res_to_dev_res add_size 1000 min_align 1000
[ 0.400626] pci 0000:00:1c.0: res[13]=[io 0x1000-0x1fff] res_to_dev_res add_size 1000 min_align 1000
[ 0.400630] pci 0000:00:1c.0: BAR 14: assigned [mem 0xf2100000-0xf22fffff]
[ 0.400635] pci 0000:00:1c.0: BAR 15: assigned [mem 0xf2300000-0xf24fffff 64bit pref]
[ 0.400637] pci 0000:00:1c.0: BAR 13: assigned [io 0x2000-0x2fff]
[ 0.400639] pci 0000:00:01.0: PCI bridge to [bus 01]
[ 0.400641] pci 0000:00:01.0: bridge window [io 0xe000-0xefff]
[ 0.400643] pci 0000:00:01.0: bridge window [mem 0xf6000000-0xf70fffff]
[ 0.400645] pci 0000:00:01.0: bridge window [mem 0xe0000000-0xf1ffffff 64bit pref]
[ 0.400647] pci 0000:00:1c.0: PCI bridge to [bus 02]
[ 0.400650] pci 0000:00:1c.0: bridge window [io 0x2000-0x2fff]
[ 0.400654] pci 0000:00:1c.0: bridge window [mem 0xf2100000-0xf22fffff]
[ 0.400658] pci 0000:00:1c.0: bridge window [mem 0xf2300000-0xf24fffff 64bit pref]
[ 0.400663] pci 0000:00:1c.1: PCI bridge to [bus 03]
[ 0.400667] pci 0000:00:1c.1: bridge window [mem 0xf7300000-0xf73fffff]
[ 0.400675] pci 0000:04:00.0: BAR 6: assigned [mem 0xf7200000-0xf720ffff pref]
[ 0.400677] pci 0000:00:1c.3: PCI bridge to [bus 04]
[ 0.400679] pci 0000:00:1c.3: bridge window [io 0xd000-0xdfff]
[ 0.400684] pci 0000:00:1c.3: bridge window [mem 0xf7200000-0xf72fffff]
[ 0.400691] pci 0000:00:1c.4: PCI bridge to [bus 05]
[ 0.400696] pci 0000:00:1c.4: bridge window [mem 0xf7100000-0xf71fffff]
[ 0.400703] pci 0000:06:00.0: PCI bridge to [bus 07]
[ 0.400722] pci 0000:00:1c.6: PCI bridge to [bus 06-07]
[ 0.400733] pci_bus 0000:00: resource 4 [io 0x0000-0x0cf7 window]
[ 0.400734] pci_bus 0000:00: resource 5 [io 0x0d00-0xffff window]
[ 0.400736] pci_bus 0000:00: resource 6 [mem 0x000a0000-0x000bffff window]
[ 0.400737] pci_bus 0000:00: resource 7 [mem 0x000d0000-0x000d3fff window]
[ 0.400738] pci_bus 0000:00: resource 8 [mem 0x000d4000-0x000d7fff window]
[ 0.400739] pci_bus 0000:00: resource 9 [mem 0x000d8000-0x000dbfff window]
[ 0.400740] pci_bus 0000:00: resource 10 [mem 0x000dc000-0x000dffff window]
[ 0.400741] pci_bus 0000:00: resource 11 [mem 0x000e0000-0x000e3fff window]
[ 0.400742] pci_bus 0000:00: resource 12 [mem 0x000e4000-0x000e7fff window]
[ 0.400744] pci_bus 0000:00: resource 13 [mem 0xe0000000-0xfeafffff window]
[ 0.400745] pci_bus 0000:01: resource 0 [io 0xe000-0xefff]
[ 0.400746] pci_bus 0000:01: resource 1 [mem 0xf6000000-0xf70fffff]
[ 0.400747] pci_bus 0000:01: resource 2 [mem 0xe0000000-0xf1ffffff 64bit pref]
[ 0.400748] pci_bus 0000:02: resource 0 [io 0x2000-0x2fff]
[ 0.400749] pci_bus 0000:02: resource 1 [mem 0xf2100000-0xf22fffff]
[ 0.400751] pci_bus 0000:02: resource 2 [mem 0xf2300000-0xf24fffff 64bit pref]
[ 0.400752] pci_bus 0000:03: resource 1 [mem 0xf7300000-0xf73fffff]
[ 0.400753] pci_bus 0000:04: resource 0 [io 0xd000-0xdfff]
[ 0.400754] pci_bus 0000:04: resource 1 [mem 0xf7200000-0xf72fffff]
[ 0.400755] pci_bus 0000:05: resource 1 [mem 0xf7100000-0xf71fffff]
[ 0.400756] pci_bus 0000:06: resource 4 [io 0x0000-0x0cf7 window]
[ 0.400757] pci_bus 0000:06: resource 5 [io 0x0d00-0xffff window]
[ 0.400759] pci_bus 0000:06: resource 6 [mem 0x000a0000-0x000bffff window]
[ 0.400760] pci_bus 0000:06: resource 7 [mem 0x000d0000-0x000d3fff window]
[ 0.400761] pci_bus 0000:06: resource 8 [mem 0x000d4000-0x000d7fff window]
[ 0.400762] pci_bus 0000:06: resource 9 [mem 0x000d8000-0x000dbfff window]
[ 0.400763] pci_bus 0000:06: resource 10 [mem 0x000dc000-0x000dffff window]
[ 0.400764] pci_bus 0000:06: resource 11 [mem 0x000e0000-0x000e3fff window]
[ 0.400765] pci_bus 0000:06: resource 12 [mem 0x000e4000-0x000e7fff window]
[ 0.400767] pci_bus 0000:06: resource 13 [mem 0xe0000000-0xfeafffff window]
[ 0.400768] pci_bus 0000:07: resource 4 [io 0x0000-0x0cf7 window]
[ 0.400769] pci_bus 0000:07: resource 5 [io 0x0d00-0xffff window]
[ 0.400770] pci_bus 0000:07: resource 6 [mem 0x000a0000-0x000bffff window]
[ 0.400771] pci_bus 0000:07: resource 7 [mem 0x000d0000-0x000d3fff window]
[ 0.400772] pci_bus 0000:07: resource 8 [mem 0x000d4000-0x000d7fff window]
[ 0.400773] pci_bus 0000:07: resource 9 [mem 0x000d8000-0x000dbfff window]
[ 0.400775] pci_bus 0000:07: resource 10 [mem 0x000dc000-0x000dffff window]
[ 0.400776] pci_bus 0000:07: resource 11 [mem 0x000e0000-0x000e3fff window]
[ 0.400777] pci_bus 0000:07: resource 12 [mem 0x000e4000-0x000e7fff window]
[ 0.400778] pci_bus 0000:07: resource 13 [mem 0xe0000000-0xfeafffff window]
[ 0.400799] NET: Registered protocol family 2
[ 0.400940] TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
[ 0.401112] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
[ 0.401208] TCP: Hash tables configured (established 131072 bind 65536)
[ 0.401233] UDP hash table entries: 8192 (order: 6, 262144 bytes)
[ 0.401275] UDP-Lite hash table entries: 8192 (order: 6, 262144 bytes)
[ 0.401333] NET: Registered protocol family 1
[ 0.653924] pci 0000:01:00.0: Video device with shadowed ROM
[ 0.654152] PCI: CLS 64 bytes, default 64
[ 0.654189] Trying to unpack rootfs image as initramfs...
[ 1.040867] Freeing initrd memory: 34712K (ffff880033c24000 - ffff880035e0a000)
[ 1.040889] PCI-DMA: Using software bounce buffering for IO (SWIOTLB)
[ 1.040891] software IO TLB [mem 0xdab91000-0xdeb91000] (64MB) mapped at [ffff8800dab91000-ffff8800deb90fff]
[ 1.040943] RAPL PMU detected, API unit is 2^-32 Joules, 3 fixed counters 163840 ms ovfl timer
[ 1.040944] hw unit of domain pp0-core 2^-16 Joules
[ 1.040945] hw unit of domain package 2^-16 Joules
[ 1.040946] hw unit of domain pp1-gpu 2^-16 Joules
[ 1.041086] Scanning for low memory corruption every 60 seconds
[ 1.041352] futex hash table entries: 2048 (order: 5, 131072 bytes)
[ 1.041379] audit: initializing netlink subsys (disabled)
[ 1.041389] audit: type=2000 audit(1464322139.824:1): initialized
[ 1.041734] Initialise system trusted keyring
[ 1.041855] HugeTLB registered 2 MB page size, pre-allocated 0 pages
[ 1.042918] zbud: loaded
[ 1.043068] VFS: Disk quotas dquot_6.6.0
[ 1.043092] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[ 1.043426] fuse init (API version 7.23)
[ 1.043519] Key type big_key registered
[ 1.043535] Allocating IMA MOK and blacklist keyrings.
[ 1.043836] Key type asymmetric registered
[ 1.043839] Asymmetric key parser 'x509' registered
[ 1.043864] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 249)
[ 1.043899] io scheduler noop registered
[ 1.043901] io scheduler deadline registered (default)
[ 1.043924] io scheduler cfq registered
[ 1.044333] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 1.044338] pciehp: PCI Express Hot Plug Controller Driver version: 0.4
[ 1.044361] intel_idle: MWAIT substates: 0x1120
[ 1.044362] intel_idle: v0.4.1 model 0x2A
[ 1.044363] intel_idle: lapic_timer_reliable_states 0xffffffff
[ 1.044604] input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input0
[ 1.044607] ACPI: Power Button [PWRB]
[ 1.044633] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input1
[ 1.044634] ACPI: Power Button [PWRF]
[ 1.045208] thermal LNXTHERM:00: registered as thermal_zone0
[ 1.045209] ACPI: Thermal Zone [TZ00] (28 C)
[ 1.045374] thermal LNXTHERM:01: registered as thermal_zone1
[ 1.045375] ACPI: Thermal Zone [TZ01] (30 C)
[ 1.045399] GHES: HEST is not enabled!
[ 1.045471] Serial: 8250/16550 driver, 32 ports, IRQ sharing enabled
[ 1.046638] Linux agpgart interface v0.103
[ 1.049035] brd: module loaded
[ 1.050094] loop: module loaded
[ 1.050249] libphy: Fixed MDIO Bus: probed
[ 1.050252] tun: Universal TUN/TAP device driver, 1.6
[ 1.050252] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[ 1.050285] PPP generic driver version 2.4.2
[ 1.050328] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 1.050332] ehci-pci: EHCI PCI platform driver
[ 1.050405] ehci-pci 0000:00:1a.0: EHCI Host Controller
[ 1.050410] ehci-pci 0000:00:1a.0: new USB bus registered, assigned bus number 1
[ 1.050420] ehci-pci 0000:00:1a.0: debug port 2
[ 1.054332] ehci-pci 0000:00:1a.0: cache line size of 64 is not supported
[ 1.054344] ehci-pci 0000:00:1a.0: irq 16, io mem 0xf7428000
[ 1.065795] ehci-pci 0000:00:1a.0: USB 2.0 started, EHCI 1.00
[ 1.065824] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 1.065826] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.065827] usb usb1: Product: EHCI Host Controller
[ 1.065828] usb usb1: Manufacturer: Linux 4.4.0-22-generic ehci_hcd
[ 1.065829] usb usb1: SerialNumber: 0000:00:1a.0
[ 1.065997] hub 1-0:1.0: USB hub found
[ 1.066005] hub 1-0:1.0: 2 ports detected
[ 1.066167] ehci-pci 0000:00:1d.0: EHCI Host Controller
[ 1.066170] ehci-pci 0000:00:1d.0: new USB bus registered, assigned bus number 2
[ 1.066180] ehci-pci 0000:00:1d.0: debug port 2
[ 1.070078] ehci-pci 0000:00:1d.0: cache line size of 64 is not supported
[ 1.070087] ehci-pci 0000:00:1d.0: irq 23, io mem 0xf7427000
[ 1.081850] ehci-pci 0000:00:1d.0: USB 2.0 started, EHCI 1.00
[ 1.081904] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
[ 1.081906] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.081907] usb usb2: Product: EHCI Host Controller
[ 1.081908] usb usb2: Manufacturer: Linux 4.4.0-22-generic ehci_hcd
[ 1.081909] usb usb2: SerialNumber: 0000:00:1d.0
[ 1.082049] hub 2-0:1.0: USB hub found
[ 1.082055] hub 2-0:1.0: 2 ports detected
[ 1.082134] ehci-platform: EHCI generic platform driver
[ 1.082142] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 1.082146] ohci-pci: OHCI PCI platform driver
[ 1.082152] ohci-platform: OHCI generic platform driver
[ 1.082158] uhci_hcd: USB Universal Host Controller Interface driver
[ 1.082220] xhci_hcd 0000:03:00.0: xHCI Host Controller
[ 1.082224] xhci_hcd 0000:03:00.0: new USB bus registered, assigned bus number 3
[ 1.143355] xhci_hcd 0000:03:00.0: hcc params 0x0200f180 hci version 0x96 quirks 0x00080000
[ 1.143528] usb usb3: New USB device found, idVendor=1d6b, idProduct=0002
[ 1.143529] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.143530] usb usb3: Product: xHCI Host Controller
[ 1.143532] usb usb3: Manufacturer: Linux 4.4.0-22-generic xhci-hcd
[ 1.143533] usb usb3: SerialNumber: 0000:03:00.0
[ 1.143688] hub 3-0:1.0: USB hub found
[ 1.143698] hub 3-0:1.0: 2 ports detected
[ 1.143764] xhci_hcd 0000:03:00.0: xHCI Host Controller
[ 1.143767] xhci_hcd 0000:03:00.0: new USB bus registered, assigned bus number 4
[ 1.143787] usb usb4: We don't know the algorithms for LPM for this host, disabling LPM.
[ 1.143799] usb usb4: New USB device found, idVendor=1d6b, idProduct=0003
[ 1.143800] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.143801] usb usb4: Product: xHCI Host Controller
[ 1.143802] usb usb4: Manufacturer: Linux 4.4.0-22-generic xhci-hcd
[ 1.143803] usb usb4: SerialNumber: 0000:03:00.0
[ 1.143936] hub 4-0:1.0: USB hub found
[ 1.143946] hub 4-0:1.0: 2 ports detected
[ 1.144058] xhci_hcd 0000:05:00.0: xHCI Host Controller
[ 1.144062] xhci_hcd 0000:05:00.0: new USB bus registered, assigned bus number 5
[ 1.205188] xhci_hcd 0000:05:00.0: hcc params 0x0200f180 hci version 0x96 quirks 0x00080000
[ 1.205365] usb usb5: New USB device found, idVendor=1d6b, idProduct=0002
[ 1.205366] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.205367] usb usb5: Product: xHCI Host Controller
[ 1.205369] usb usb5: Manufacturer: Linux 4.4.0-22-generic xhci-hcd
[ 1.205370] usb usb5: SerialNumber: 0000:05:00.0
[ 1.205533] hub 5-0:1.0: USB hub found
[ 1.205543] hub 5-0:1.0: 2 ports detected
[ 1.205609] xhci_hcd 0000:05:00.0: xHCI Host Controller
[ 1.205611] xhci_hcd 0000:05:00.0: new USB bus registered, assigned bus number 6
[ 1.205631] usb usb6: We don't know the algorithms for LPM for this host, disabling LPM.
[ 1.205643] usb usb6: New USB device found, idVendor=1d6b, idProduct=0003
[ 1.205644] usb usb6: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.205645] usb usb6: Product: xHCI Host Controller
[ 1.205646] usb usb6: Manufacturer: Linux 4.4.0-22-generic xhci-hcd
[ 1.205647] usb usb6: SerialNumber: 0000:05:00.0
[ 1.205714] hub 6-0:1.0: USB hub found
[ 1.205721] hub 6-0:1.0: 2 ports detected
[ 1.205811] i8042: PNP: No PS/2 controller found. Probing ports directly.
[ 1.208278] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 1.208283] serio: i8042 AUX port at 0x60,0x64 irq 12
[ 1.208489] mousedev: PS/2 mouse device common for all mice
[ 1.208758] rtc_cmos 00:02: RTC can wake from S4
[ 1.208907] rtc_cmos 00:02: rtc core: registered rtc_cmos as rtc0
[ 1.208936] rtc_cmos 00:02: alarms up to one month, y3k, 242 bytes nvram, hpet irqs
[ 1.208943] i2c /dev entries driver
[ 1.208977] device-mapper: uevent: version 1.0.3
[ 1.209026] device-mapper: ioctl: 4.34.0-ioctl (2015-10-28) initialised: dm-devel@redhat.com
[ 1.209037] Intel P-state driver initializing.
[ 1.209430] ledtrig-cpu: registered to indicate activity on CPUs
[ 1.209962] NET: Registered protocol family 10
[ 1.210336] NET: Registered protocol family 17
[ 1.210352] Key type dns_resolver registered
[ 1.210830] microcode: CPU0 sig=0x206a7, pf=0x2, revision=0x29
[ 1.210838] microcode: CPU1 sig=0x206a7, pf=0x2, revision=0x29
[ 1.210874] microcode: CPU2 sig=0x206a7, pf=0x2, revision=0x29
[ 1.210913] microcode: CPU3 sig=0x206a7, pf=0x2, revision=0x29
[ 1.210952] microcode: CPU4 sig=0x206a7, pf=0x2, revision=0x29
[ 1.210966] microcode: CPU5 sig=0x206a7, pf=0x2, revision=0x29
[ 1.211010] microcode: CPU6 sig=0x206a7, pf=0x2, revision=0x29
[ 1.211050] microcode: CPU7 sig=0x206a7, pf=0x2, revision=0x29
[ 1.211146] microcode: Microcode Update Driver: v2.01 <tigran@aivazian.fsnet.co.uk>, Peter Oruba

[ 1.211484] registered taskstats version 1
[ 1.211516] Loading compiled-in X.509 certificates
[ 1.212944] Loaded X.509 cert 'Build time autogenerated kernel key: 10281ca0c0463cd0680138fff55319c9bd7d63b8'
[ 1.212973] zswap: loaded using pool lzo/zbud
[ 1.215043] Key type trusted registered
[ 1.218298] Key type encrypted registered
[ 1.218303] AppArmor: AppArmor sha1 policy hashing enabled
[ 1.218306] ima: No TPM chip found, activating TPM-bypass!
[ 1.218323] evm: HMAC attrs: 0x1
[ 1.218695] Magic number: 0:509:111
[ 1.218835] rtc_cmos 00:02: setting system clock to 2016-05-27 04:09:00 UTC (1464322140)
[ 1.218970] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found
[ 1.218970] EDD information not available.
[ 1.219018] PM: Hibernation image not present or could not be loaded.
[ 1.220053] Freeing unused kernel memory: 1480K (ffffffff81f41000 - ffffffff820b3000)
[ 1.220054] Write protecting the kernel read-only data: 14336k
[ 1.220424] Freeing unused kernel memory: 1868K (ffff88000182d000 - ffff880001a00000)
[ 1.220741] Freeing unused kernel memory: 176K (ffff880001dd4000 - ffff880001e00000)
[ 1.227270] random: systemd-udevd urandom read with 2 bits of entropy available
[ 1.248453] FUJITSU Extended Socket Network Device Driver - version 1.0 - Copyright (c) 2015 FUJITSU LIMITED
[ 1.256754] pps_core: LinuxPPS API ver. 1 registered
[ 1.256756] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[ 1.257728] PTP clock support registered
[ 1.260677] ahci 0000:00:1f.2: version 3.0
[ 1.260964] e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k
[ 1.260965] e1000e: Copyright(c) 1999 - 2015 Intel Corporation.
[ 1.273841] ahci 0000:00:1f.2: AHCI 0001.0300 32 slots 6 ports 6 Gbps 0x2b impl SATA mode
[ 1.273845] ahci 0000:00:1f.2: flags: 64bit ncq pm led clo pio slum part ems apst
[ 1.298436] scsi host0: ahci
[ 1.298656] scsi host1: ahci
[ 1.298812] scsi host2: ahci
[ 1.298980] scsi host3: ahci
[ 1.299068] scsi host4: ahci
[ 1.299137] scsi host5: ahci
[ 1.299167] ata1: SATA max UDMA/133 abar m2048@0xf7426000 port 0xf7426100 irq 42
[ 1.299169] ata2: SATA max UDMA/133 abar m2048@0xf7426000 port 0xf7426180 irq 42
[ 1.299170] ata3: DUMMY
[ 1.299172] ata4: SATA max UDMA/133 abar m2048@0xf7426000 port 0xf7426280 irq 42
[ 1.299173] ata5: DUMMY
[ 1.299175] ata6: SATA max UDMA/133 abar m2048@0xf7426000 port 0xf7426380 irq 42
[ 1.299322] e1000e 0000:00:19.0: Interrupt Throttling Rate (ints/sec) set to dynamic conservative mode
[ 1.299390] ahci 0000:04:00.0: AHCI 0001.0100 32 slots 2 ports 3 Gbps 0x3 impl SATA mode
[ 1.299394] ahci 0000:04:00.0: flags: 64bit ncq pm led clo pmp pio slum part
[ 1.299607] scsi host6: ahci
[ 1.299683] scsi host7: ahci
[ 1.299715] ata7: SATA max UDMA/133 abar m512@0xf7210000 port 0xf7210100 irq 19
[ 1.299718] ata8: SATA max UDMA/133 abar m512@0xf7210000 port 0xf7210180 irq 19
[ 1.381793] usb 1-1: new high-speed USB device number 2 using ehci-pci
[ 1.397792] usb 2-1: new high-speed USB device number 2 using ehci-pci
[ 1.514167] usb 1-1: New USB device found, idVendor=8087, idProduct=0024
[ 1.514169] usb 1-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[ 1.514421] hub 1-1:1.0: USB hub found
[ 1.514522] hub 1-1:1.0: 6 ports detected
[ 1.530215] usb 2-1: New USB device found, idVendor=8087, idProduct=0024
[ 1.530217] usb 2-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[ 1.530727] hub 2-1:1.0: USB hub found
[ 1.530955] hub 2-1:1.0: 8 ports detected
[ 1.559875] e1000e 0000:00:19.0 eth0: registered PHC clock
[ 1.559877] e1000e 0000:00:19.0 eth0: (PCI Express:2.5GT/s:Width x1) c8:60:00:16:9a:ec
[ 1.559879] e1000e 0000:00:19.0 eth0: Intel(R) PRO/1000 Network Connection
[ 1.559909] e1000e 0000:00:19.0 eth0: MAC: 10, PHY: 11, PBA No: FFFFFF-0FF
[ 1.560525] e1000e 0000:00:19.0 eno1: renamed from eth0
[ 1.617847] ata7: SATA link down (SStatus 0 SControl 300)
[ 1.617851] ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 1.617902] ata4: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 1.617929] ata8: SATA link down (SStatus 0 SControl 300)
[ 1.617951] ata1: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
[ 1.618976] ACPI Error: [DSSP] Namespace lookup failure, AE_NOT_FOUND (20150930/psargs-359)
[ 1.618985] ACPI Error: Method parse/execution failed [\_SB.PCI0.SAT0.SPT3._GTF] (Node ffff88040e0cd690), AE_NOT_FOUND (20150930/psparse-542)
[ 1.619043] ACPI Error: [DSSP] Namespace lookup failure, AE_NOT_FOUND (20150930/psargs-359)
[ 1.619047] ACPI Error: Method parse/execution failed [\_SB.PCI0.SAT0.SPT1._GTF] (Node ffff88040e0cd5a0), AE_NOT_FOUND (20150930/psparse-542)
[ 1.619160] ata4.00: ATA-8: ST31000528AS, CC3E, max UDMA/133
[ 1.619165] ata4.00: 1953525168 sectors, multi 16: LBA48 NCQ (depth 31/32)
[ 1.619466] ata2.00: ATA-8: ST3750330AS, SD15, max UDMA/133
[ 1.619471] ata2.00: 1465149168 sectors, multi 16: LBA48 NCQ (depth 31/32)
[ 1.620413] ACPI Error: [DSSP] Namespace lookup failure, AE_NOT_FOUND (20150930/psargs-359)
[ 1.620422] ACPI Error: Method parse/execution failed [\_SB.PCI0.SAT0.SPT3._GTF] (Node ffff88040e0cd690), AE_NOT_FOUND (20150930/psparse-542)
[ 1.620572] ata4.00: configured for UDMA/133
[ 1.621053] ACPI Error: [DSSP] Namespace lookup failure, AE_NOT_FOUND (20150930/psargs-359)
[ 1.621062] ACPI Error: Method parse/execution failed [\_SB.PCI0.SAT0.SPT1._GTF] (Node ffff88040e0cd5a0), AE_NOT_FOUND (20150930/psparse-542)
[ 1.621500] ata2.00: configured for UDMA/133
[ 1.621798] ata6: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 1.623532] ACPI Error: [DSSP] Namespace lookup failure, AE_NOT_FOUND (20150930/psargs-359)
[ 1.623541] ACPI Error: Method parse/execution failed [\_SB.PCI0.SAT0.SPT5._GTF] (Node ffff88040e0cd780), AE_NOT_FOUND (20150930/psparse-542)
[ 1.623555] ata6.00: ATAPI: Optiarc DVD RW AD-5260S, 1.00, max UDMA/100
[ 1.625634] ACPI Error: [DSSP] Namespace lookup failure, AE_NOT_FOUND (20150930/psargs-359)
[ 1.625642] ACPI Error: Method parse/execution failed [\_SB.PCI0.SAT0.SPT5._GTF] (Node ffff88040e0cd780), AE_NOT_FOUND (20150930/psparse-542)
[ 1.625658] ata6.00: configured for UDMA/100
[ 1.659121] ACPI Error: [DSSP] Namespace lookup failure, AE_NOT_FOUND (20150930/psargs-359)
[ 1.659130] ACPI Error: Method parse/execution failed [\_SB.PCI0.SAT0.SPT0._GTF] (Node ffff88040e0cd528), AE_NOT_FOUND (20150930/psparse-542)
[ 1.694901] ata1.00: ATA-8: OCZ-VERTEX3, 2.13, max UDMA/133
[ 1.694906] ata1.00: 234441648 sectors, multi 16: LBA48 NCQ (depth 31/32), AA
[ 1.731105] ACPI Error: [DSSP] Namespace lookup failure, AE_NOT_FOUND (20150930/psargs-359)
[ 1.731114] ACPI Error: Method parse/execution failed [\_SB.PCI0.SAT0.SPT0._GTF] (Node ffff88040e0cd528), AE_NOT_FOUND (20150930/psparse-542)
[ 1.771397] ata1.00: configured for UDMA/133
[ 1.771809] scsi 0:0:0:0: Direct-Access ATA OCZ-VERTEX3 2.13 PQ: 0 ANSI: 5
[ 1.772098] sd 0:0:0:0: [sda] 234441648 512-byte logical blocks: (120 GB/112 GiB)
[ 1.772123] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 1.772143] sd 0:0:0:0: [sda] Write Protect is off
[ 1.772145] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 1.772161] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 1.772385] scsi 1:0:0:0: Direct-Access ATA ST3750330AS SD15 PQ: 0 ANSI: 5
[ 1.772614] sd 1:0:0:0: [sdb] 1465149168 512-byte logical blocks: (750 GB/699 GiB)
[ 1.772641] sd 1:0:0:0: Attached scsi generic sg1 type 0
[ 1.772669] sd 1:0:0:0: [sdb] Write Protect is off
[ 1.772672] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[ 1.772700] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 1.772761] scsi 3:0:0:0: Direct-Access ATA ST31000528AS CC3E PQ: 0 ANSI: 5
[ 1.772890] sd 3:0:0:0: [sdc] 1953525168 512-byte logical blocks: (1.00 TB/932 GiB)
[ 1.772891] sd 3:0:0:0: Attached scsi generic sg2 type 0
[ 1.772956] sd 3:0:0:0: [sdc] Write Protect is off
[ 1.772959] sd 3:0:0:0: [sdc] Mode Sense: 00 3a 00 00
[ 1.772983] sd 3:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 1.773526] sda: sda2 sda3
[ 1.773794] sd 0:0:0:0: [sda] Attached SCSI disk
[ 1.774237] scsi 5:0:0:0: CD-ROM Optiarc DVD RW AD-5260S 1.00 PQ: 0 ANSI: 5
[ 1.779529] sdb: sdb1 < sdb5 >
[ 1.779897] sd 1:0:0:0: [sdb] Attached SCSI disk
[ 1.791680] sr 5:0:0:0: [sr0] scsi3-mmc drive: 48x/48x writer cd/rw xa/form2 cdda tray
[ 1.791685] cdrom: Uniform CD-ROM driver Revision: 3.20
[ 1.791882] sr 5:0:0:0: Attached scsi CD-ROM sr0
[ 1.791992] sr 5:0:0:0: Attached scsi generic sg3 type 5
[ 1.794183] sdc: sdc1
[ 1.794746] sd 3:0:0:0: [sdc] Attached SCSI disk
[ 1.801787] usb 2-1.1: new full-speed USB device number 3 using ehci-pci
[ 1.897982] usb 2-1.1: New USB device found, idVendor=046d, idProduct=c52b
[ 1.897987] usb 2-1.1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 1.897989] usb 2-1.1: Product: USB Receiver
[ 1.897992] usb 2-1.1: Manufacturer: Logitech
[ 1.902589] hidraw: raw HID events driver (C) Jiri Kosina
[ 1.911502] usbcore: registered new interface driver usbhid
[ 1.911503] usbhid: USB HID core driver
[ 1.915175] logitech-djreceiver 0003:046D:C52B.0003: hiddev0,hidraw0: USB HID v1.11 Device [Logitech USB Receiver] on usb-0000:00:1d.0-1.1/input2
[ 1.969766] usb 2-1.4: new full-speed USB device number 4 using ehci-pci
[ 2.037768] tsc: Refined TSC clocksource calibration: 3411.126 MHz
[ 2.037770] clocksource: tsc: mask: 0xffffffffffffffff max_cycles: 0x312b5d0590b, max_idle_ns: 440795367236 ns
[ 2.050631] input: Logitech M705 as /devices/pci0000:00/0000:00:1d.0/usb2/2-1/2-1.1/2-1.1:1.2/0003:046D:C52B.0003/0003:046D:101B.0004/input/input5
[ 2.050732] logitech-hidpp-device 0003:046D:101B.0004: input,hidraw1: USB HID v1.11 Mouse [Logitech M705] on usb-0000:00:1d.0-1.1:1
[ 2.064215] usb 2-1.4: New USB device found, idVendor=1ea7, idProduct=5001
[ 2.064217] usb 2-1.4: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 2.064218] usb 2-1.4: Product: Gaming Keyboard
[ 2.064219] usb 2-1.4: Manufacturer: WFDZ
[ 2.070456] input: WFDZ Gaming Keyboard as /devices/pci0000:00/0000:00:1d.0/usb2/2-1/2-1.4/2-1.4:1.0/0003:1EA7:5001.0005/input/input6
[ 2.125828] hid-generic 0003:1EA7:5001.0005: input,hidraw2: USB HID v1.10 Keyboard [WFDZ Gaming Keyboard] on usb-0000:00:1d.0-1.4/input0
[ 2.137758] usb 2-1.7: new full-speed USB device number 5 using ehci-pci
[ 2.165652] input: WFDZ Gaming Keyboard as /devices/pci0000:00/0000:00:1d.0/usb2/2-1/2-1.4/2-1.4:1.1/0003:1EA7:5001.0006/input/input7
[ 2.217867] hid-generic 0003:1EA7:5001.0006: input,hiddev0,hidraw3: USB HID v1.10 Mouse [WFDZ Gaming Keyboard] on usb-0000:00:1d.0-1.4/input1
[ 2.230208] usb 2-1.7: New USB device found, idVendor=0cf3, idProduct=3000
[ 2.230210] usb 2-1.7: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[ 2.276930] EXT4-fs (sda2): mounted filesystem with ordered data mode. Opts: (null)
[ 2.352052] systemd[1]: systemd 229 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ -LZ4 +SECCOMP +BLKID +ELFUTILS +KMOD -IDN)
[ 2.352173] systemd[1]: Detected architecture x86-64.
[ 2.352392] systemd[1]: Set hostname to <erikoksanen>.
[ 2.423888] systemd[1]: Set up automount Arbitrary Executable File Formats File System Automount Point.
[ 2.423977] systemd[1]: Created slice User and Session Slice.
[ 2.424005] systemd[1]: Listening on /dev/initctl Compatibility Named Pipe.
[ 2.424050] systemd[1]: Listening on Journal Audit Socket.
[ 2.424062] systemd[1]: Reached target Remote File Systems (Pre).
[ 2.424120] systemd[1]: Created slice System Slice.
[ 2.424135] systemd[1]: Reached target Slices.
[ 2.424146] systemd[1]: Reached target Remote File Systems.
[ 2.424178] systemd[1]: Listening on Journal Socket.
[ 2.437902] systemd[1]: Starting Uncomplicated firewall...
[ 2.437956] systemd[1]: Listening on Journal Socket (/dev/log).
[ 2.437984] systemd[1]: Listening on Syslog Socket.
[ 2.438302] systemd[1]: Starting Journal Service...
[ 2.438335] systemd[1]: Listening on udev Kernel Socket.
[ 2.440287] systemd[1]: Starting Load Kernel Modules...
[ 2.440624] systemd[1]: Mounting POSIX Message Queue File System...
[ 2.441026] systemd[1]: Mounting Debug File System...
[ 2.441365] systemd[1]: Starting Create list of required static device nodes for the current kernel...
[ 2.441392] systemd[1]: Reached target Encrypted Volumes.
[ 2.441451] systemd[1]: Started Forward Password Requests to Wall Directory Watch.
[ 2.441771] systemd[1]: Mounting Huge Pages File System...
[ 2.441822] systemd[1]: Listening on udev Control Socket.
[ 2.441852] systemd[1]: Reached target User and Group Name Lookups.
[ 2.442279] systemd[1]: Started Braille Device Support.
[ 2.442427] systemd[1]: Listening on fsck to fsckd communication Socket.
[ 2.442518] systemd[1]: Created slice system-getty.slice.
[ 2.442857] systemd[1]: Started Read required files in advance.
[ 2.444094] systemd[1]: Started Uncomplicated firewall.
[ 2.445067] systemd[1]: Started Create list of required static device nodes for the current kernel.
[ 2.451386] systemd[1]: Mounted Debug File System.
[ 2.451436] systemd[1]: Mounted POSIX Message Queue File System.
[ 2.451478] systemd[1]: Mounted Huge Pages File System.
[ 2.456768] lp: driver loaded but no devices found
[ 2.458790] ppdev: user-space parallel port driver
[ 2.464129] systemd[1]: Starting Create Static Device Nodes in /dev...
[ 2.464514] systemd[1]: Started Load Kernel Modules.
[ 2.464873] systemd[1]: Starting Apply Kernel Variables...
[ 2.465184] systemd[1]: Mounting FUSE Control File System...
[ 2.467024] systemd[1]: Mounted FUSE Control File System.
[ 2.470654] systemd[1]: Started Apply Kernel Variables.
[ 2.476320] systemd[1]: Started Create Static Device Nodes in /dev.
[ 2.476676] systemd[1]: Starting udev Kernel Device Manager...
[ 2.482992] systemd[1]: Started Journal Service.
[ 2.510158] EXT4-fs (sda2): re-mounted. Opts: errors=remount-ro
[ 2.528958] systemd-journald[272]: Received request to flush runtime journal from PID 1
[ 2.577169] wmi: Mapper loaded
[ 2.605768] ACPI Warning: SystemIO range 0x0000000000000428-0x000000000000042F conflicts with OpRegion 0x0000000000000400-0x000000000000047F (\PMIO) (20150930/utaddress-254)
[ 2.605774] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
[ 2.605778] ACPI Warning: SystemIO range 0x0000000000000540-0x000000000000054F conflicts with OpRegion 0x0000000000000500-0x0000000000000563 (\GPIO) (20150930/utaddress-254)
[ 2.605782] ACPI Warning: SystemIO range 0x0000000000000540-0x000000000000054F conflicts with OpRegion 0x0000000000000500-0x000000000000057F (\_SB_.PCI0.LPCB.GPBX) (20150930/utaddress-254)
[ 2.605786] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
[ 2.605787] ACPI Warning: SystemIO range 0x0000000000000530-0x000000000000053F conflicts with OpRegion 0x0000000000000500-0x0000000000000563 (\GPIO) (20150930/utaddress-254)
[ 2.605790] ACPI Warning: SystemIO range 0x0000000000000530-0x000000000000053F conflicts with OpRegion 0x0000000000000500-0x000000000000057F (\_SB_.PCI0.LPCB.GPBX) (20150930/utaddress-254)
[ 2.605794] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
[ 2.605795] ACPI Warning: SystemIO range 0x0000000000000500-0x000000000000052F conflicts with OpRegion 0x0000000000000500-0x0000000000000563 (\GPIO) (20150930/utaddress-254)
[ 2.605798] ACPI Warning: SystemIO range 0x0000000000000500-0x000000000000052F conflicts with OpRegion 0x0000000000000500-0x000000000000057F (\_SB_.PCI0.LPCB.GPBX) (20150930/utaddress-254)
[ 2.605801] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
[ 2.605802] lpc_ich: Resource conflict(s) found affecting gpio_ich
[ 2.607743] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[ 2.609642] audit: type=1400 audit(1464322141.884:2): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/bin/ubuntu-core-launcher" pid=497 comm="apparmor_parser"
[ 2.688044] audit: type=1400 audit(1464322141.964:3): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/sbin/ippusbxd" pid=510 comm="apparmor_parser"
[ 2.693477] audit: type=1400 audit(1464322141.968:4): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/sbin/dhclient" pid=494 comm="apparmor_parser"
[ 2.693485] audit: type=1400 audit(1464322141.968:5): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=494 comm="apparmor_parser"
[ 2.693491] audit: type=1400 audit(1464322141.968:6): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/lib/NetworkManager/nm-dhcp-helper" pid=494 comm="apparmor_parser"
[ 2.693496] audit: type=1400 audit(1464322141.968:7): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/lib/connman/scripts/dhclient-script" pid=494 comm="apparmor_parser"
[ 2.698981] audit: type=1400 audit(1464322141.976:8): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/lib/lightdm/lightdm-guest-session" pid=493 comm="apparmor_parser"
[ 2.698990] audit: type=1400 audit(1464322141.976:9): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/lib/lightdm/lightdm-guest-session//chromium" pid=493 comm="apparmor_parser"
[ 2.700201] audit: type=1400 audit(1464322141.976:10): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/sbin/tcpdump" pid=524 comm="apparmor_parser"
[ 2.702393] [drm] Initialized drm 1.1.0 20060810
[ 2.708122] random: nonblocking pool is initialized
[ 2.713019] AVX version of gcm_enc/dec engaged.
[ 2.713021] AES CTR mode by8 optimization enabled
[ 2.815194] snd_hda_intel 0000:01:00.1: Disabling MSI
[ 2.815197] snd_hda_intel 0000:01:00.1: Handle vga_switcheroo audio client
[ 2.846283] Adding 16743236k swap on /dev/sda3. Priority:-1 extents:1 across:16743236k SSFS
[ 2.858494] snd_hda_codec_realtek hdaudioC0D0: autoconfig for ALC892: line_outs=4 (0x14/0x15/0x16/0x17/0x0) type:line
[ 2.858498] snd_hda_codec_realtek hdaudioC0D0: speaker_outs=0 (0x0/0x0/0x0/0x0/0x0)
[ 2.858501] snd_hda_codec_realtek hdaudioC0D0: hp_outs=1 (0x1b/0x0/0x0/0x0/0x0)
[ 2.858503] snd_hda_codec_realtek hdaudioC0D0: mono: mono_out=0x0
[ 2.858505] snd_hda_codec_realtek hdaudioC0D0: dig-out=0x11/0x1e
[ 2.858507] snd_hda_codec_realtek hdaudioC0D0: inputs:
[ 2.858509] snd_hda_codec_realtek hdaudioC0D0: Front Mic=0x19
[ 2.858512] snd_hda_codec_realtek hdaudioC0D0: Rear Mic=0x18
[ 2.858514] snd_hda_codec_realtek hdaudioC0D0: Line=0x1a
[ 2.864220] kvm: disabled by bios
[ 2.872289] input: HDA Intel PCH Front Mic as /devices/pci0000:00/0000:00:1b.0/sound/card0/input8
[ 2.872378] input: HDA Intel PCH Rear Mic as /devices/pci0000:00/0000:00:1b.0/sound/card0/input9
[ 2.872466] input: HDA Intel PCH Line as /devices/pci0000:00/0000:00:1b.0/sound/card0/input10
[ 2.872572] input: HDA Intel PCH Line Out Front as /devices/pci0000:00/0000:00:1b.0/sound/card0/input11
[ 2.872677] input: HDA Intel PCH Line Out Surround as /devices/pci0000:00/0000:00:1b.0/sound/card0/input12
[ 2.872763] input: HDA Intel PCH Line Out CLFE as /devices/pci0000:00/0000:00:1b.0/sound/card0/input13
[ 2.873179] input: HDA Intel PCH Line Out Side as /devices/pci0000:00/0000:00:1b.0/sound/card0/input14
[ 2.873236] input: HDA Intel PCH Front Headphone as /devices/pci0000:00/0000:00:1b.0/sound/card0/input15
[ 2.874148] asus_wmi: ASUS WMI generic driver loaded
[ 2.880296] asus_wmi: Initialization: 0x0
[ 2.880326] asus_wmi: BIOS WMI version: 0.9
[ 2.880374] asus_wmi: SFUN value: 0x0
[ 2.880710] input: Eee PC WMI hotkeys as /devices/platform/eeepc-wmi/input/input16
[ 2.880871] asus_wmi: Number of fans: 1
[ 2.884000] nvidia: module license 'NVIDIA' taints kernel.
[ 2.884003] Disabling lock debugging due to kernel taint
[ 2.887932] nvidia: module verification failed: signature and/or required key missing - tainting kernel
[ 2.892944] cgroup: new mount options do not match the existing superblock, will be ignored
[ 2.914625] intel_rapl: Found RAPL domain package
[ 2.914629] intel_rapl: Found RAPL domain core
[ 2.914631] intel_rapl: Found RAPL domain uncore
[ 2.914636] intel_rapl: RAPL package 0 domain package locked by BIOS
[ 2.915379] vgaarb: device changed decodes: PCI:0000:01:00.0,olddecodes=io+mem,decodes=none:owns=io+mem
[ 2.915505] [drm] Initialized nvidia-drm 0.0.0 20150116 for 0000:01:00.0 on minor 0
[ 2.915511] NVRM: loading NVIDIA UNIX x86_64 Kernel Module 304.131 Sun Nov 8 21:43:33 PST 2015
[ 3.037871] clocksource: Switched to clocksource tsc
[ 3.654436] IPv6: ADDRCONF(NETDEV_UP): eno1: link is not ready
[ 3.694088] input: HDA NVidia HDMI/DP,pcm=3 as /devices/pci0000:00/0000:00:01.0/0000:01:00.1/sound/card1/input17
[ 3.694141] input: HDA NVidia HDMI/DP,pcm=7 as /devices/pci0000:00/0000:00:01.0/0000:01:00.1/sound/card1/input18
[ 3.694188] input: HDA NVidia HDMI/DP,pcm=8 as /devices/pci0000:00/0000:00:01.0/0000:01:00.1/sound/card1/input19
[ 3.694232] input: HDA NVidia HDMI/DP,pcm=9 as /devices/pci0000:00/0000:00:01.0/0000:01:00.1/sound/card1/input20
[ 3.909849] IPv6: ADDRCONF(NETDEV_UP): eno1: link is not ready
[ 4.036394] Bluetooth: Core ver 2.21
[ 4.036407] NET: Registered protocol family 31
[ 4.036408] Bluetooth: HCI device and connection manager initialized
[ 4.036411] Bluetooth: HCI socket layer initialized
[ 4.036413] Bluetooth: L2CAP socket layer initialized
[ 4.036418] Bluetooth: SCO socket layer initialized
[ 4.293836] usbcore: registered new interface driver ath3k
[ 4.421779] usb 2-1.7: USB disconnect, device number 5
[ 5.237517] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[ 5.237519] Bluetooth: BNEP filters: protocol multicast
[ 5.237522] Bluetooth: BNEP socket layer initialized
[ 5.625639] usb 2-1.7: new full-speed USB device number 6 using ehci-pci
[ 5.631679] e1000e: eno1 NIC Link is Up 100 Mbps Full Duplex, Flow Control: None
[ 5.631682] e1000e 0000:00:19.0 eno1: 10/100 speed: disabling TSO
[ 5.631718] IPv6: ADDRCONF(NETDEV_CHANGE): eno1: link becomes ready
[ 5.726580] usb 2-1.7: New USB device found, idVendor=0cf3, idProduct=3005
[ 5.726595] usb 2-1.7: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[ 5.741483] usbcore: registered new interface driver btusb
[ 10.002695] Bluetooth: RFCOMM TTY layer initialized
[ 10.002701] Bluetooth: RFCOMM socket layer initialized
[ 10.002706] Bluetooth: RFCOMM ver 1.11
[ 6264.278121] usb 1-1.2: new high-speed USB device number 3 using ehci-pci
[ 6264.382435] usb 1-1.2: New USB device found, idVendor=05e3, idProduct=0745
[ 6264.382442] usb 1-1.2: New USB device strings: Mfr=0, Product=1, SerialNumber=2
[ 6264.382446] usb 1-1.2: Product: USB Storage
[ 6264.382451] usb 1-1.2: SerialNumber: 000000000903
[ 6264.405170] usb-storage 1-1.2:1.0: USB Mass Storage device detected
[ 6264.405270] scsi host8: usb-storage 1-1.2:1.0
[ 6264.405393] usbcore: registered new interface driver usb-storage
[ 6264.407978] usbcore: registered new interface driver uas
[ 6265.403743] scsi 8:0:0:0: Direct-Access Generic STORAGE DEVICE 0903 PQ: 0 ANSI: 6
[ 6265.404459] sd 8:0:0:0: Attached scsi generic sg4 type 0
[ 6265.722352] sd 8:0:0:0: [sdd] 31116288 512-byte logical blocks: (15.9 GB/14.8 GiB)
[ 6265.723822] sd 8:0:0:0: [sdd] Write Protect is off
[ 6265.723828] sd 8:0:0:0: [sdd] Mode Sense: 21 00 00 00
[ 6265.725321] sd 8:0:0:0: [sdd] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[ 6265.740836] sdd: sdd1
[ 6265.745415] sd 8:0:0:0: [sdd] Attached SCSI removable disk
[ 6265.952192] FAT-fs (sdd1): Volume was not properly unmounted. Some data may be corrupt. Please run fsck.
[ 6282.273368] EXT4-fs (sdc1): warning: maximal mount count reached, running e2fsck is recommended
[ 6282.296264] EXT4-fs (sdc1): mounted filesystem with ordered data mode. Opts: (null)
[ 6303.644850] usb 1-1.2: USB disconnect, device number 3
erikoksanen@erikoksanen:~

[ 6265.952192] FAT-fs (sdd1): Volume was not properly unmounted. Some data may be corrupt. Please run fsck.
[ 6282.273368] EXT4-fs (sdc1): warning: maximal mount count reached, running e2fsck is recommended

erikoksanen@erikoksanen:~$ fsck
fsck från util-linux 2.27.1
e2fsck 1.42.13 (17-May-2015)
/dev/sda2 är monterat.



VARNING!!! Filsystemet är monterat. Om du fortsätter ***KOMMER***
du att orsaka ***ALLVARLIG*** skada på filsystemet.


Vill du verkligen fortsätta<n>?

[ 6265.952192] FAT-fs (sdd1): Volume was not properly unmounted. Some data may be corrupt. Please run fsck.
[ 6282.273368] EXT4-fs (sdc1): warning: maximal mount count reached, running e2fsck is recommended

umount /dev/sdc1
sudo fsck /dev/sdc1

nisse2 skrev: dev/sdd1 - finns inte är det cdrom eller någon sd-kort eller liknande jag använt?

nisse2 skrev: Ska jag köra detta komando på denna disk (sdc1)?

Kod: Markera allt

umount /dev/sdc1
sudo fsck /dev/sdc1

sudo umount /dev/sdc1
sudo fsck /dev/sdc1

erikoksanen@erikoksanen:~$ sudo umount /dev/sdc1
[sudo] password for erikoksanen:
umount: /dev/sdc1: not mounted
erikoksanen@erikoksanen:~$ sudo fsck /dev/sdc1
fsck från util-linux 2.27.1
e2fsck 1.42.13 (17-May-2015)
/dev/sdc1 har monterats 1784 gånger utan att kontrolleras, kontroll framtvingad.
Pass 1: Kontrollerar inoder, block och storlekar
Pass 2: Kontrollerar katalogstruktur
Pass 3: Kontrollerar katalogförbindelser
/lost+found inte funnen. Skapa<j>? ja

Pass 4: Kontrollerar referensräknare
Pass 5: Kontrollerar gruppsammanfattningsinformation

/dev/sdc1: ***** FILSYSTEMET MODIFIERADES *****
/dev/sdc1: 44995/61054976 filer (16.7% ej sammanhängande), 132264307/244190208 block
erikoksanen@erikoksanen:~$
erikoksanen@erikoksanen:~$

erikoksanen@erikoksanen:~$ dmesg | tail -50
[ 798.280926] sd 9:0:0:0: [sdd] Write cache: enabled, read cache: enabled, supports DPO and FUA
[ 798.303169] sdd: sdd1
[ 798.307938] sd 9:0:0:0: [sdd] Attached SCSI disk
[ 798.542155] FAT-fs (sdd1): Volume was not properly unmounted. Some data may be corrupt. Please run fsck.
[ 4400.095364] EXT4-fs (sdb1): mounted filesystem with ordered data mode. Opts: (null)
[20728.986753] show_signal_msg: 51 callbacks suppressed
[20728.986758] kdenlive[7647]: segfault at 20 ip 0000000000000020 sp 00007ffdfbb13b18 error 14
[27452.072664] usb 1-1.1: USB disconnect, device number 4
[27452.292430] sd 9:0:0:0: [sdd] Synchronizing SCSI cache
[27452.441959] sd 9:0:0:0: [sdd] Synchronize Cache(10) failed: Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK
[27453.864824] usb 1-1.2: USB disconnect, device number 3
[27454.449479] sd 8:0:0:0: [sdc] Synchronizing SCSI cache
[27454.570165] sd 8:0:0:0: [sdc] Synchronize Cache(10) failed: Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK
[27535.846142] usb 1-1.2: new high-speed USB device number 5 using ehci-pci
[27535.940711] usb 1-1.2: New USB device found, idVendor=090c, idProduct=1000
[27535.940716] usb 1-1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[27535.940719] usb 1-1.2: Product: USB DISK
[27535.940721] usb 1-1.2: Manufacturer: SMI
[27535.940723] usb 1-1.2: SerialNumber: AALEFE8A40EWYK3S
[27535.941219] usb-storage 1-1.2:1.0: USB Mass Storage device detected
[27535.941594] scsi host10: usb-storage 1-1.2:1.0
[27537.515478] scsi 10:0:0:0: Direct-Access SMI USB DISK 1100 PQ: 0 ANSI: 4
[27537.516104] sd 10:0:0:0: Attached scsi generic sg3 type 0
[27537.516653] sd 10:0:0:0: [sdc] 15826944 512-byte logical blocks: (8.10 GB/7.55 GiB)
[27537.517393] sd 10:0:0:0: [sdc] Write Protect is off
[27537.517397] sd 10:0:0:0: [sdc] Mode Sense: 43 00 00 00
[27537.518313] sd 10:0:0:0: [sdc] No Caching mode page found
[27537.518319] sd 10:0:0:0: [sdc] Assuming drive cache: write through
[27537.523395] sdc: sdc1
[27537.526393] sd 10:0:0:0: [sdc] Attached SCSI removable disk
[27537.743549] FAT-fs (sdc1): Volume was not properly unmounted. Some data may be corrupt. Please run fsck.
[27771.258284] usb 1-1.2: USB disconnect, device number 5
[31494.958884] usb 1-1.2: new high-speed USB device number 6 using ehci-pci
[31495.063255] usb 1-1.2: New USB device found, idVendor=05e3, idProduct=0745
[31495.063260] usb 1-1.2: New USB device strings: Mfr=0, Product=1, SerialNumber=2
[31495.063263] usb 1-1.2: Product: USB Storage
[31495.063265] usb 1-1.2: SerialNumber: 000000000903
[31495.064068] usb-storage 1-1.2:1.0: USB Mass Storage device detected
[31495.064321] scsi host11: usb-storage 1-1.2:1.0
[31496.064771] scsi 11:0:0:0: Direct-Access Generic STORAGE DEVICE 0903 PQ: 0 ANSI: 6
[31496.065361] sd 11:0:0:0: Attached scsi generic sg3 type 0
[31496.403364] sd 11:0:0:0: [sdc] 31116288 512-byte logical blocks: (15.9 GB/14.8 GiB)
[31496.404865] sd 11:0:0:0: [sdc] Write Protect is off
[31496.404871] sd 11:0:0:0: [sdc] Mode Sense: 21 00 00 00
[31496.406350] sd 11:0:0:0: [sdc] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[31496.422157] sdc: sdc1
[31496.426950] sd 11:0:0:0: [sdc] Attached SCSI removable disk
[31496.630633] FAT-fs (sdc1): Volume was not properly unmounted. Some data may be corrupt. Please run fsck.
[31543.167309] usb 1-1.2: USB disconnect, device number 6
[32914.278808] perf interrupt took too long (2506 > 2500), lowering kernel.perf_event_max_sample_rate to 50000
erikoksanen@erikoksanen:~$

erikoksanen@erikoksanen:~$ tail -50 /var/log/syslog
May 30 13:32:27 erikoksanen org.freedesktop.FileManager1[1880]: (eog:12429): EOG-WARNING **: Failed to open file '/home/erikoksanen/.cache/thumbnails/normal/c2e6b062cd49cff72308b9b76e21829e.png': Filen eller katalogen finns inte
May 30 13:32:33 erikoksanen org.freedesktop.FileManager1[1880]: (eog:12429): EOG-WARNING **: Failed to open file '/home/erikoksanen/.cache/thumbnails/normal/0fc1e7a891de702d41d49d965091f819.png': Filen eller katalogen finns inte
May 30 13:33:17 erikoksanen org.gtk.vfs.Daemon[1880]: ** (process:2279): WARNING **: send_done_cb: Inget sådant gränssnitt ”org.gtk.vfs.Enumerator” på objekt med sökvägen /org/gtk/vfs/client/enumerator/19 (g-dbus-error-quark, 19)
May 30 13:34:26 erikoksanen systemd[1]: Started CUPS Scheduler.
May 30 13:34:26 erikoksanen colord[1000]: (colord:1000): Cd-WARNING **: failed to get session [pid 12472]: Enheten eller adressen finns inte
May 30 13:36:36 erikoksanen dbus[744]: [system] Activating via systemd: service name='org.freedesktop.hostname1' unit='dbus-org.freedesktop.hostname1.service'
May 30 13:36:36 erikoksanen systemd[1]: Starting Hostname Service...
May 30 13:36:36 erikoksanen dbus[744]: [system] Successfully activated service 'org.freedesktop.hostname1'
May 30 13:36:36 erikoksanen systemd[1]: Started Hostname Service.
May 30 13:36:36 erikoksanen org.gtk.vfs.Daemon[1880]: ** (process:2279): WARNING **: send_infos_cb: Inget sådant gränssnitt ”org.gtk.vfs.Enumerator” på objekt med sökvägen /org/gtk/vfs/client/enumerator/2 (g-dbus-error-quark, 19)
May 30 13:36:36 erikoksanen org.gtk.vfs.Daemon[1880]: ** (process:2279): WARNING **: send_done_cb: Inget sådant gränssnitt ”org.gtk.vfs.Enumerator” på objekt med sökvägen /org/gtk/vfs/client/enumerator/2 (g-dbus-error-quark, 19)
May 30 13:37:23 erikoksanen org.freedesktop.FileManager1[1880]: [export_job] exported to `/media/erikoksanen/bffa3475-e037-4215-9241-457473b81167/alla_fotos_202/test_500mm/slade/100D5100/darktable/DSC_0004.tif'
May 30 13:37:37 erikoksanen org.freedesktop.FileManager1[1880]: (gimp-2.8:12557): GLib-GObject-WARNING **: g_object_set_valist: object class 'GeglConfig' has no property named 'cache-size'
May 30 13:37:37 erikoksanen org.freedesktop.FileManager1[1880]: (gimp-2.8:12557): GEGL-gegl-operation.c-WARNING **: Cannot change name of operation class 0xE38710 from "gimp:point-layer-mode" to "gimp:dissolve-mode"
May 30 13:37:37 erikoksanen org.freedesktop.FileManager1[1880]: (gimp-2.8:12557): GEGL-gegl-operation.c-WARNING **: Cannot change name of operation class 0xE38BE0 from "gimp:point-layer-mode" to "gimp:behind-mode"
May 30 13:37:37 erikoksanen org.freedesktop.FileManager1[1880]: (gimp-2.8:12557): GEGL-gegl-operation.c-WARNING **: Cannot change name of operation class 0xE393A0 from "gimp:point-layer-mode" to "gimp:multiply-mode"
May 30 13:37:37 erikoksanen org.freedesktop.FileManager1[1880]: (gimp-2.8:12557): GEGL-gegl-operation.c-WARNING **: Cannot change name of operation class 0xE39680 from "gimp:point-layer-mode" to "gimp:screen-mode"
May 30 13:37:37 erikoksanen org.freedesktop.FileManager1[1880]: (gimp-2.8:12557): GEGL-gegl-operation.c-WARNING **: Cannot change name of operation class 0xE39A70 from "gimp:point-layer-mode" to "gimp:overlay-mode"
May 30 13:37:37 erikoksanen org.freedesktop.FileManager1[1880]: (gimp-2.8:12557): GEGL-gegl-operation.c-WARNING **: Cannot change name of operation class 0xE39EA0 from "gimp:point-layer-mode" to "gimp:difference-mode"
May 30 13:37:37 erikoksanen org.freedesktop.FileManager1[1880]: (gimp-2.8:12557): GEGL-gegl-operation.c-WARNING **: Cannot change name of operation class 0xE3A260 from "gimp:point-layer-mode" to "gimp:addition-mode"
May 30 13:37:37 erikoksanen org.freedesktop.FileManager1[1880]: (gimp-2.8:12557): GEGL-gegl-operation.c-WARNING **: Cannot change name of operation class 0xE3A6A0 from "gimp:point-layer-mode" to "gimp:subtract-mode"
May 30 13:37:37 erikoksanen org.freedesktop.FileManager1[1880]: (gimp-2.8:12557): GEGL-gegl-operation.c-WARNING **: Cannot change name of operation class 0xE3AA60 from "gimp:point-layer-mode" to "gimp:darken-only-mode"
May 30 13:37:37 erikoksanen org.freedesktop.FileManager1[1880]: (gimp-2.8:12557): GEGL-gegl-operation.c-WARNING **: Cannot change name of operation class 0xE3AEB0 from "gimp:point-layer-mode" to "gimp:lighten-only-mode"
May 30 13:37:37 erikoksanen org.freedesktop.FileManager1[1880]: (gimp-2.8:12557): GEGL-gegl-operation.c-WARNING **: Cannot change name of operation class 0xE3B250 from "gimp:point-layer-mode" to "gimp:hue-mode"
May 30 13:37:37 erikoksanen org.freedesktop.FileManager1[1880]: (gimp-2.8:12557): GEGL-gegl-operation.c-WARNING **: Cannot change name of operation class 0xE3BE20 from "gimp:point-layer-mode" to "gimp:saturation-mode"
May 30 13:37:37 erikoksanen org.freedesktop.FileManager1[1880]: (gimp-2.8:12557): GEGL-gegl-operation.c-WARNING **: Cannot change name of operation class 0xE3C450 from "gimp:point-layer-mode" to "gimp:color-mode"
May 30 13:37:37 erikoksanen org.freedesktop.FileManager1[1880]: (gimp-2.8:12557): GEGL-gegl-operation.c-WARNING **: Cannot change name of operation class 0xE3C6D0 from "gimp:point-layer-mode" to "gimp:value-mode"
May 30 13:37:37 erikoksanen org.freedesktop.FileManager1[1880]: (gimp-2.8:12557): GEGL-gegl-operation.c-WARNING **: Cannot change name of operation class 0xE3CA50 from "gimp:point-layer-mode" to "gimp:divide-mode"
May 30 13:37:37 erikoksanen org.freedesktop.FileManager1[1880]: (gimp-2.8:12557): GEGL-gegl-operation.c-WARNING **: Cannot change name of operation class 0xE3CED0 from "gimp:point-layer-mode" to "gimp:dodge-mode"
May 30 13:37:37 erikoksanen org.freedesktop.FileManager1[1880]: (gimp-2.8:12557): GEGL-gegl-operation.c-WARNING **: Cannot change name of operation class 0xE3D240 from "gimp:point-layer-mode" to "gimp:burn-mode"
May 30 13:37:37 erikoksanen org.freedesktop.FileManager1[1880]: (gimp-2.8:12557): GEGL-gegl-operation.c-WARNING **: Cannot change name of operation class 0xE3D690 from "gimp:point-layer-mode" to "gimp:hardlight-mode"
May 30 13:37:37 erikoksanen org.freedesktop.FileManager1[1880]: (gimp-2.8:12557): GEGL-gegl-operation.c-WARNING **: Cannot change name of operation class 0xE3DA30 from "gimp:point-layer-mode" to "gimp:softlight-mode"
May 30 13:37:37 erikoksanen org.freedesktop.FileManager1[1880]: (gimp-2.8:12557): GEGL-gegl-operation.c-WARNING **: Cannot change name of operation class 0xE3DE30 from "gimp:point-layer-mode" to "gimp:grain-extract-mode"
May 30 13:37:37 erikoksanen org.freedesktop.FileManager1[1880]: (gimp-2.8:12557): GEGL-gegl-operation.c-WARNING **: Cannot change name of operation class 0xE3E290 from "gimp:point-layer-mode" to "gimp:grain-merge-mode"
May 30 13:37:37 erikoksanen org.freedesktop.FileManager1[1880]: (gimp-2.8:12557): GEGL-gegl-operation.c-WARNING **: Cannot change name of operation class 0xE3E640 from "gimp:point-layer-mode" to "gimp:color-erase-mode"
May 30 13:37:37 erikoksanen org.freedesktop.FileManager1[1880]: (gimp-2.8:12557): GEGL-gegl-operation.c-WARNING **: Cannot change name of operation class 0xE3EA30 from "gimp:point-layer-mode" to "gimp:erase-mode"
May 30 13:37:37 erikoksanen org.freedesktop.FileManager1[1880]: (gimp-2.8:12557): GEGL-gegl-operation.c-WARNING **: Cannot change name of operation class 0xE3EE50 from "gimp:point-layer-mode" to "gimp:replace-mode"
May 30 13:37:37 erikoksanen org.freedesktop.FileManager1[1880]: (gimp-2.8:12557): GEGL-gegl-operation.c-WARNING **: Cannot change name of operation class 0xE3F220 from "gimp:point-layer-mode" to "gimp:anti-erase-mode"
May 30 13:37:42 erikoksanen org.freedesktop.FileManager1[1880]: lcms: converting from 'sRGB' to 'sRGB built-in'
May 30 13:39:59 erikoksanen systemd[1]: Started CUPS Scheduler.
May 30 13:39:59 erikoksanen colord[1000]: (colord:1000): Cd-WARNING **: failed to get session [pid 12621]: Enheten eller adressen finns inte
May 30 13:40:24 erikoksanen dbus[744]: [system] Activating via systemd: service name='org.freedesktop.hostname1' unit='dbus-org.freedesktop.hostname1.service'
May 30 13:40:24 erikoksanen systemd[1]: Starting Hostname Service...
May 30 13:40:24 erikoksanen dbus[744]: [system] Successfully activated service 'org.freedesktop.hostname1'
May 30 13:40:24 erikoksanen systemd[1]: Started Hostname Service.
May 30 13:46:24 erikoksanen smartd[782]: Device: /dev/sdb [SAT], SMART Usage Attribute: 190 Airflow_Temperature_Cel changed from 67 to 66
May 30 13:46:24 erikoksanen smartd[782]: Device: /dev/sdb [SAT], SMART Usage Attribute: 194 Temperature_Celsius changed from 33 to 34
May 30 13:52:59 erikoksanen systemd[1]: Started CUPS Scheduler.
May 30 13:52:59 erikoksanen colord[1000]: (colord:1000): Cd-WARNING **: failed to get session [pid 12973]: Enheten eller adressen finns inte
May 30 13:54:51 erikoksanen kernel: [32914.278808] perf interrupt took too long (2506 > 2500), lowering kernel.perf_event_max_sample_rate to 50000
erikoksanen@erikoksanen:~$