Sida 1 av 2
Radeon grafikkort
Postat: 08 aug 2007, 19:41
av blaeffo
Hejsan
Jag har förstått (tror jag) att det finns problem med ATI-grafikkort och Ubuntu?
Är det alltså så att man behöver installera några speciella drivrutiner för att allt ska funka?
Jag hittade min väg till Restricted drivers management och enablade at-drivern som fanns där, men då kunde jag inte ha högre upplösning än 1024x768 sen...
Jag har också sett vissa krångliga guider på internet för hur man installerar nån drivrutin...
Men det jag egentligen undrar är, behöver man nånting överhuvudtaget, och i så fall, vilket är det lättaste/bästa sättet att fixa det på?
Jag har ett Radeon 9600...
Och jag är ganska supernoob på ubuntu

SV: Radeon grafikkort
Postat: 08 aug 2007, 19:43
av zenbios
SV: Radeon grafikkort
Postat: 08 aug 2007, 19:49
av TForsman
Sitter själv med Radeon 9600, borde funka bra med envy till ditt kort.
Efter du har installerat grafik korts drivrutiner, så kör detta i terminalen:
Och skriv här vad du får för resultat. Då ser vi om det funkade eller inte.
SV: Radeon grafikkort
Postat: 08 aug 2007, 20:12
av blaeffo
Det här är vad jag får för svar efter att ha kört envy och skrivit det där kommandot:
Kod: Markera allt
Xlib: extension "XFree86-DRI" missing on display ":0.0".
display: :0.0 screen: 0
OpenGL vendor string: Mesa project: www.mesa3d.org
OpenGL renderer string: Mesa GLX Indirect
OpenGL version string: 1.4 (1.5 Mesa 6.5.2)
SV: Radeon grafikkort
Postat: 08 aug 2007, 20:29
av TForsman
inte bra
Börja göra backup på Xorg:
http://ubuntu-se.org/mediawiki/index.php/XorgBackup
Installera 8.39.4 Drivrutin manuellt
Ta hem ATI drivrutiner:
ati-driver-installer-8.39.4-x86.x86_64.run (den här installationen är för 32bit och 64bit systems).
Lägg filen i din Hemmapp i datorn.
Först göra filen körvänlig:
Kod: Markera allt
chmod a+x ati-driver-installer-8.39.4-x86.x86_64.run
Sen börja installera den:
Kod: Markera allt
sudo bash ./ati-driver-installer-8.39.4-x86.x86_64.run
Och följ anvisningarna på skärmen.
Sen när det är klart, gör detta i terminalen:
Sen starta om datan.
Sen skriv i terminalen:
SV: Radeon grafikkort
Postat: 08 aug 2007, 21:18
av blaeffo
Det går bra fram tills det näst sista kodstycket, alltså precis innan jag ska starta om datorn..
Det här är vad jag får, och jag antar att nåt inte funkade...
Kod: Markera allt
blaeffo@magnus9:~$ aticonfig --initial --force
Uninitialised file found, configuring.
Using /etc/X11/xorg.conf
Saved back-up to /etc/X11/xorg.conf.fglrx-0
aticonfig: Writing to '/etc/X11/xorg.conf' failed. Bad file descriptor.
SV: Radeon grafikkort
Postat: 08 aug 2007, 21:20
av TForsman
SV: Radeon grafikkort
Postat: 08 aug 2007, 21:28
av blaeffo
Kod: Markera allt
display: :0.0 screen: 0
OpenGL vendor string: ATI Technologies Inc.
OpenGL renderer string: ATI RADEON 9600 Series
OpenGL version string: 2.0.6650 (8.39.4)
SV: Radeon grafikkort
Postat: 08 aug 2007, 21:35
av blaeffo
Jag antar att det är som det ska nu.. men en sak bara... Jag vill ha upplösning 1280x960.. det finns inte listan, så jag tvingas ha 1280x1024...
Innan fixade jag det genom att ändra lite i xorg.conf, men nu har den här installationen ändrat där så det jag ändrade på då är borta... kan man lösa det på nåt sätt?
Tack så jättemycket för hjälpen förresten!

SV: Radeon grafikkort
Postat: 08 aug 2007, 22:00
av TForsman
blaeffo skrev:
Jag antar att det är som det ska nu.. men en sak bara... Jag vill ha upplösning 1280x960.. det finns inte listan, så jag tvingas ha 1280x1024...
Innan fixade jag det genom att ändra lite i xorg.conf, men nu har den här installationen ändrat där så det jag ändrade på då är borta... kan man lösa det på nåt sätt?
Tack så jättemycket för hjälpen förresten!
Skönt att det ordnade sig med grafiken. Du kan ändra igen i Xorg....bara du pillar bara på upplösningen igen så borde det funka klockrent.
SV: Radeon grafikkort
Postat: 08 aug 2007, 22:36
av blaeffo
Jag lyckas inte få till det... jag har gjort på så många olika sätt, men hur jag än pillar så går den bara tillbaks till att högsta möjliga upplösningen är 1024x768...
När jag har låtit den auto-configa enligt den metoden du angav ovan så kan jag alltså ha 1280x1024 som högst... men som sagt vill jag ha 1280x960...
Så här ser min xorg.conf ut nu (alltså efter att den auto-configurats):
Kod: Markera allt
# /etc/X11/xorg.conf (xorg X Window System server configuration file)
#
# This file was generated by dexconf, the Debian X Configuration tool, using
# values from the debconf database.
#
# Edit this file with caution, and see the xorg.conf(5) manual page.
# (Type "man xorg.conf" at the shell prompt.)
#
# This file is automatically updated on xserver-xorg package upgrades *only*
# if it has not been modified since the last upgrade of the xserver-xorg
# package.
#
# If you have edited this file but would like it to be automatically updated
# again, run the following command:
# sudo dpkg-reconfigure -phigh xserver-xorg
Section "ServerLayout"
Identifier "Default Layout"
Screen 0 "aticonfig-Screen[0]" 0 0
InputDevice "Generic Keyboard"
InputDevice "Configured Mouse"
InputDevice "stylus" "SendCoreEvents"
InputDevice "cursor" "SendCoreEvents"
InputDevice "eraser" "SendCoreEvents"
EndSection
Section "Files"
# path to defoma fonts
FontPath "/usr/share/fonts/X11/misc"
FontPath "/usr/share/fonts/X11/cyrillic"
FontPath "/usr/share/fonts/X11/100dpi/:unscaled"
FontPath "/usr/share/fonts/X11/75dpi/:unscaled"
FontPath "/usr/share/fonts/X11/Type1"
FontPath "/usr/share/fonts/X11/100dpi"
FontPath "/usr/share/fonts/X11/75dpi"
FontPath "/var/lib/defoma/x-ttcidfont-conf.d/dirs/TrueType"
EndSection
Section "Module"
Load "i2c"
Load "bitmap"
Load "ddc"
Load "dri"
Load "extmod"
Load "freetype"
Load "glx"
Load "int10"
Load "vbe"
EndSection
Section "InputDevice"
Identifier "Generic Keyboard"
Driver "kbd"
Option "CoreKeyboard"
Option "XkbRules" "xorg"
Option "XkbModel" "pc105"
Option "XkbLayout" "us"
EndSection
Section "InputDevice"
Identifier "Configured Mouse"
Driver "mouse"
Option "CorePointer"
Option "Device" "/dev/input/mice"
Option "Protocol" "ImPS/2"
Option "ZAxisMapping" "4 5"
Option "Emulate3Buttons" "true"
EndSection
Section "InputDevice"
Identifier "stylus"
Driver "wacom"
Option "Device" "/dev/input/wacom"
Option "Type" "stylus"
Option "ForceDevice" "ISDV4" # Tablet PC ONLY
EndSection
Section "InputDevice"
Identifier "eraser"
Driver "wacom"
Option "Device" "/dev/input/wacom"
Option "Type" "eraser"
Option "ForceDevice" "ISDV4" # Tablet PC ONLY
EndSection
Section "InputDevice"
Identifier "cursor"
Driver "wacom"
Option "Device" "/dev/input/wacom"
Option "Type" "cursor"
Option "ForceDevice" "ISDV4" # Tablet PC ONLY
EndSection
Section "Monitor"
Identifier "aticonfig-Monitor[0]"
Option "VendorName" "ATI Proprietary Driver"
Option "ModelName" "Generic Autodetecting Monitor"
Option "DPMS" "true"
EndSection
Section "Device"
Identifier "aticonfig-Device[0]"
Driver "fglrx"
EndSection
Section "Screen"
Identifier "aticonfig-Screen[0]"
Device "aticonfig-Device[0]"
Monitor "aticonfig-Monitor[0]"
DefaultDepth 24
SubSection "Display"
Viewport 0 0
Depth 24
EndSubSection
EndSection
Section "DRI"
Mode 0666
EndSection
Section "Extensions"
Option "Composite" "Disable"
EndSection
Och så här såg den ut innan jag ens installerade drivrutinerna för grafikkortet.. Och då funkade 1280x960 jättebra:
Kod: Markera allt
# /etc/X11/xorg.conf (xorg X Window System server configuration file)
#
# This file was generated by dexconf, the Debian X Configuration tool, using
# values from the debconf database.
#
# Edit this file with caution, and see the xorg.conf(5) manual page.
# (Type "man xorg.conf" at the shell prompt.)
#
# This file is automatically updated on xserver-xorg package upgrades *only*
# if it has not been modified since the last upgrade of the xserver-xorg
# package.
#
# If you have edited this file but would like it to be automatically updated
# again, run the following command:
# sudo dpkg-reconfigure -phigh xserver-xorg
Section "Files"
FontPath "/usr/share/fonts/X11/misc"
FontPath "/usr/share/fonts/X11/cyrillic"
FontPath "/usr/share/fonts/X11/100dpi/:unscaled"
FontPath "/usr/share/fonts/X11/75dpi/:unscaled"
FontPath "/usr/share/fonts/X11/Type1"
FontPath "/usr/share/fonts/X11/100dpi"
FontPath "/usr/share/fonts/X11/75dpi"
# path to defoma fonts
FontPath "/var/lib/defoma/x-ttcidfont-conf.d/dirs/TrueType"
EndSection
Section "Module"
Load "i2c"
Load "bitmap"
Load "ddc"
Load "dri"
Load "extmod"
Load "freetype"
Load "glx"
Load "int10"
Load "vbe"
EndSection
Section "InputDevice"
Identifier "Generic Keyboard"
Driver "kbd"
Option "CoreKeyboard"
Option "XkbRules" "xorg"
Option "XkbModel" "pc105"
Option "XkbLayout" "us"
EndSection
Section "InputDevice"
Identifier "Configured Mouse"
Driver "mouse"
Option "CorePointer"
Option "Device" "/dev/input/mice"
Option "Protocol" "ImPS/2"
Option "ZAxisMapping" "4 5"
Option "Emulate3Buttons" "true"
EndSection
Section "InputDevice"
Driver "wacom"
Identifier "stylus"
Option "Device" "/dev/input/wacom"
Option "Type" "stylus"
Option "ForceDevice" "ISDV4" # Tablet PC ONLY
EndSection
Section "InputDevice"
Driver "wacom"
Identifier "eraser"
Option "Device" "/dev/input/wacom"
Option "Type" "eraser"
Option "ForceDevice" "ISDV4" # Tablet PC ONLY
EndSection
Section "InputDevice"
Driver "wacom"
Identifier "cursor"
Option "Device" "/dev/input/wacom"
Option "Type" "cursor"
Option "ForceDevice" "ISDV4" # Tablet PC ONLY
EndSection
Section "Device"
Identifier "ATI Technologies Inc RV350 AR [Radeon 9600]"
Driver "ati"
BusID "PCI:1:0:0"
EndSection
Section "Monitor"
Identifier "DELL E771p"
HorizSync 30.0 - 65.0
VertRefresh 50.0 - 75.0
Option "DPMS"
EndSection
Section "Screen"
Identifier "Default Screen"
Device "ATI Technologies Inc RV350 AR [Radeon 9600]"
Monitor "DELL E771p"
DefaultDepth 24
SubSection "Display"
Depth 1
Modes "1280x960" "1024x768" "800x600" "640x480"
EndSubSection
SubSection "Display"
Depth 4
Modes "1280x960" "1024x768" "800x600" "640x480"
EndSubSection
SubSection "Display"
Depth 8
Modes "1280x960" "1024x768" "800x600" "640x480"
EndSubSection
SubSection "Display"
Depth 15
Modes "1280x960" "1024x768" "800x600" "640x480"
EndSubSection
SubSection "Display"
Depth 16
Modes "1280x960" "1024x768" "800x600" "640x480"
EndSubSection
SubSection "Display"
Depth 24
Modes "1280x960" "1024x768" "800x600" "640x480"
EndSubSection
EndSection
Section "ServerLayout"
Identifier "Default Layout"
Screen "Default Screen"
InputDevice "Generic Keyboard"
InputDevice "Configured Mouse"
InputDevice "stylus" "SendCoreEvents"
InputDevice "cursor" "SendCoreEvents"
InputDevice "eraser" "SendCoreEvents"
EndSection
Section "DRI"
Mode 0666
EndSection
SV: Radeon grafikkort
Postat: 08 aug 2007, 23:14
av TForsman
stå ut tills imorgon så ordnar det sig...du måste ta monitor sektionen + reolution från din gamla och skriva över dem sektionerna på din nya...då fixar det sig.
Jag hjälper dig imorgon, ska i säng nu....frugan väntar redan

SV: Radeon grafikkort
Postat: 09 aug 2007, 07:57
av TForsman
Kod: Markera allt
# /etc/X11/xorg.conf (xorg X Window System server configuration file)
#
# This file was generated by dexconf, the Debian X Configuration tool, using
# values from the debconf database.
#
# Edit this file with caution, and see the xorg.conf(5) manual page.
# (Type "man xorg.conf" at the shell prompt.)
#
# This file is automatically updated on xserver-xorg package upgrades *only*
# if it has not been modified since the last upgrade of the xserver-xorg
# package.
#
# If you have edited this file but would like it to be automatically updated
# again, run the following command:
# sudo dpkg-reconfigure -phigh xserver-xorg
Section "Files"
FontPath "/usr/share/fonts/X11/misc"
FontPath "/usr/share/fonts/X11/cyrillic"
FontPath "/usr/share/fonts/X11/100dpi/:unscaled"
FontPath "/usr/share/fonts/X11/75dpi/:unscaled"
FontPath "/usr/share/fonts/X11/Type1"
FontPath "/usr/share/fonts/X11/100dpi"
FontPath "/usr/share/fonts/X11/75dpi"
# path to defoma fonts
FontPath "/var/lib/defoma/x-ttcidfont-conf.d/dirs/TrueType"
EndSection
Section "Module"
Load "i2c"
Load "bitmap"
Load "ddc"
Load "dri"
Load "extmod"
Load "freetype"
Load "glx"
Load "int10"
Load "vbe"
EndSection
Section "InputDevice"
Identifier "Generic Keyboard"
Driver "kbd"
Option "CoreKeyboard"
Option "XkbRules" "xorg"
Option "XkbModel" "pc105"
Option "XkbLayout" "us"
EndSection
Section "InputDevice"
Identifier "Configured Mouse"
Driver "mouse"
Option "CorePointer"
Option "Device" "/dev/input/mice"
Option "Protocol" "ImPS/2"
Option "ZAxisMapping" "4 5"
Option "Emulate3Buttons" "true"
EndSection
Section "InputDevice"
Driver "wacom"
Identifier "stylus"
Option "Device" "/dev/input/wacom"
Option "Type" "stylus"
Option "ForceDevice" "ISDV4" # Tablet PC ONLY
EndSection
Section "InputDevice"
Driver "wacom"
Identifier "eraser"
Option "Device" "/dev/input/wacom"
Option "Type" "eraser"
Option "ForceDevice" "ISDV4" # Tablet PC ONLY
EndSection
Section "InputDevice"
Driver "wacom"
Identifier "cursor"
Option "Device" "/dev/input/wacom"
Option "Type" "cursor"
Option "ForceDevice" "ISDV4" # Tablet PC ONLY
EndSection
Section "Device"
Identifier "ATI Technologies Inc RV350 AR [Radeon 9600]"
Driver "fglrx"
BusID "PCI:1:0:0"
EndSection
Section "Monitor"
Identifier "DELL E771p"
HorizSync 30.0 - 65.0
VertRefresh 50.0 - 75.0
Option "DPMS"
EndSection
Section "Screen"
Identifier "Default Screen"
Device "ATI Technologies Inc RV350 AR [Radeon 9600]"
Monitor "DELL E771p"
DefaultDepth 24
SubSection "Display"
Depth 1
Modes "1280x960" "1024x768" "800x600" "640x480"
EndSubSection
SubSection "Display"
Depth 4
Modes "1280x960" "1024x768" "800x600" "640x480"
EndSubSection
SubSection "Display"
Depth 8
Modes "1280x960" "1024x768" "800x600" "640x480"
EndSubSection
SubSection "Display"
Depth 15
Modes "1280x960" "1024x768" "800x600" "640x480"
EndSubSection
SubSection "Display"
Depth 16
Modes "1280x960" "1024x768" "800x600" "640x480"
EndSubSection
SubSection "Display"
Depth 24
Modes "1280x960" "1024x768" "800x600" "640x480"
EndSubSection
EndSection
Section "ServerLayout"
Identifier "Default Layout"
Screen "Default Screen"
InputDevice "Generic Keyboard"
InputDevice "Configured Mouse"
InputDevice "stylus" "SendCoreEvents"
InputDevice "cursor" "SendCoreEvents"
InputDevice "eraser" "SendCoreEvents"
EndSection
Section "DRI"
Mode 0666
EndSection
Section "Extensions"
Option "Composite" "Disable"
EndSection
Den där ska funka perfekt för dig

SV: Radeon grafikkort
Postat: 11 aug 2007, 22:05
av blaeffo
Tack så jättemycket för hjälpen, men dessvärre funkar det inte...
När jag startar om datorn igen så är högsta upplösningen 1024x768 igen... :/
SV: Radeon grafikkort
Postat: 12 aug 2007, 06:34
av TForsman
Hmm, den där Xorg borde funka utan problem. Skriv i terminalen:
Så får vi se vad den säger. Om du har startat om 2 ggr eller mer nu, kolla igen om upplösningen har ändrats.
SV: Radeon grafikkort
Postat: 12 aug 2007, 13:20
av blaeffo
såhär säger den:
Kod: Markera allt
display: :0.0 screen: 0
OpenGL vendor string: ATI Technologies Inc.
OpenGL renderer string: ATI RADEON 9600 Series
OpenGL version string: 2.0.6650 (8.39.4)
Jag har startat om två gånger och det är fortfarande 1024x768 som är max :/
SV: Radeon grafikkort
Postat: 12 aug 2007, 13:35
av TForsman
Din Xorg fil ser ut som den jag skev?
SV: Radeon grafikkort
Postat: 12 aug 2007, 13:41
av blaeffo
ja, jag kopierade hela det du skrev och klistrade in det över det gamla...
och jag provade även att göra typ likadant innan jag skrev om problemet här, och det fungerade inte... :/
En annan sak som jag blir lite konfunderad över är att när jag låter xorg.conf vara som autoconfig-grejen vill att den ska, då flyttas alla ikoner på panelerna till helt konstiga ställen, och när jag högerklickar på dom så är "move"-alternativet inaktiverat... :/
SV: Radeon grafikkort
Postat: 12 aug 2007, 13:47
av TForsman
alternativen börjar ta slut
Förstår mig inte på mig din data, borde ha funkar klockrent med den där Xorg filen.
SV: Radeon grafikkort
Postat: 12 aug 2007, 14:06
av blaeffo
meeen... vad sjutton ska jag göra då då

antingen köra i lite för hög upplösning och tvingas ha allting stretchat på längden, eller ha outhärdligt låg upplösning
eller möjligtvis gå tillbaka till windows, vilket jag känner att det är lite för tidigt för..
men tack så jättemycket för hjälpen iaf, och säg gärna till om du kommer på någonting
