lm_sensors & ASUS M2NPV-VM
Postat: 29 maj 2007, 18:44
Mitt MB är ASUS M2NPV-VM med AMD 64 X2 Dual Core Processor 4800+ där jag kör Ubuntu 7.04
Både ACPI APIC support och Q_Fan är enablade i BIOS
Följde rekommendationerna hur man installerar lm_sensors och fick följande resultat (se nedan) som jag inte riktigt blir klok på.
Vad jag inte förstår är sensor utskriften:
- varför får man Core0/1 med 2 temp
- vad är CPU Temp (=+43°C ... jag har ju dual core system)
- varför går CPU fläkten så fort trots att core temp är låg
- vad är temp3
- hur får man bort dessa ALARM
- varför ör dokumentationen till lm_sensors & sensors.conf så dålig
Har kolla runt i olika forum men har kört fast ...
Tacksam för tips ...
/zkab
1) sensors ger:
k8temp-pci-00c3
Adapter: PCI adapter
Core0 Temp:
+24°C
Core0 Temp:
+22°C
Core1 Temp:
+20°C
Core1 Temp:
+24°C
it8716-isa-0290
Adapter: ISA adapter
VCore: +1.23 V (min = +0.00 V, max = +4.08 V)
3.3V: +3.25 V (min = +0.00 V, max = +4.08 V)
5V: +4.73 V (min = +0.00 V, max = +6.85 V)
12V: +11.65 V (min = +0.00 V, max = +16.32 V)
5VSB: +4.62 V (min = +0.00 V, max = +6.85 V)
VBat: +2.85 V
CPU_PWM: 1483 RPM (min = 3245 RPM) ALARM
Rear : 403 RPM (min = 3245 RPM) ALARM
CPU Temp: +43°C (low = -1°C, high = +127°C) sensor = diode
M/B Temp: +42°C (low = -1°C, high = +127°C) sensor = thermistor
Temp3: +25°C (low = -1°C, high = +127°C) sensor = thermistor
VID: +0.000 V
2) uname -a ger:
Linux 2.6.20-16-generic #2 SMP Wed May 23 01:46:23 UTC 2007 i686 GNU/Linux
3) cat /proc/cpuinfo ger:
processor : 0
vendor_id : AuthenticAMD
cpu family : 15
model : 107
model name : AMD Athlon(tm) 64 X2 Dual Core Processor 4800+
stepping : 1
cpu MHz : 2505.293
cache size : 512 KB
physical id : 0
siblings : 2
core id : 0
cpu cores : 2
fdiv_bug : no
hlt_bug : no
f00f_bug : no
coma_bug : no
fpu : yes
fpu_exception : yes
cpuid level : 1
wp : yes
flags : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat pse36 clflush mmx fxsr sse sse2 ht syscall nx mmxext fxsr_opt lm 3dnowext 3dnow pni cx16 lahf_lm cmp_legacy svm cr8legacy ts fid vid ttp tm stc [6]
bogomips : 5014.83
clflush size : 64
processor : 1
vendor_id : AuthenticAMD
cpu family : 15
model : 107
model name : AMD Athlon(tm) 64 X2 Dual Core Processor 4800+
stepping : 1
cpu MHz : 2505.293
cache size : 512 KB
physical id : 0
siblings : 2
core id : 1
cpu cores : 2
fdiv_bug : no
hlt_bug : no
f00f_bug : no
coma_bug : no
fpu : yes
fpu_exception : yes
cpuid level : 1
wp : yes
flags : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat pse36 clflush mmx fxsr sse sse2 ht syscall nx mmxext fxsr_opt lm 3dnowext 3dnow pni cx16 lahf_lm cmp_legacy svm cr8legacy ts fid vid ttp tm stc [6]
bogomips : 5010.80
clflush size : 64
4) /etc/sensors.config ser ut så här:
chip "it8716-*"
#---------------------------------------------------------------------- ZKAB
# Voltages
label in0 "VCore"
label in1 "3.3V"
label in3 "5V"
label in4 "12V"
label in7 "5VSB"
label in8 "VBat"
ignore in2
ignore in5
ignore in6
compute in3 ((6.8/10)+1)*@ , @/((6.8/10)+1)
compute in4 ((30/10)+1)*@ , @/((30/10)+1)
compute in7 ((6.8/10)+1)*@ , @/((6.8/10)+1)
# If vid (nominal CPU voltage) isn't correct, hardcode the correct value
# instead.
# set in0_min vid * 0.95
# set in0_max vid * 1.05
# set in2_min 3.3 * 0.95
# set in2_max 3.3 * 1.05
# set in3_min 5 * 0.95
# set in3_max 5 * 1.05
# set in4_min 12 * 0.95
# set in4_max 12 * 1.05
# set in7_min 5 * 0.95
# set in7_max 5 * 1.05
# The chip does not support in8 min/max
# Temperatures
# If you are lucky, the BIOS has set the proper sensor types for you.
# If your temperature readings are completely whacky you probably
# need to change the sensor types. Adujst and uncomment the
# appropriate lines below.
#
# 2 = thermistor; 3 = thermal diode; 0 = unused
# set sensor1 3
# set sensor2 3
# set sensor3 3
# If a given sensor isn't used, you will probably want to ignore it
# as well (see ignore statement right below).
# The CPU sensor can be any of temp1, temp2 or temp3 - it's motherboard
# dependent. Same for the motherboard temperature.
label temp1 "CPU Temp"
label temp2 "M/B Temp"
label temp3 "Temp3"
# ignore temp3
# set temp1_over 60
# set temp1_low 10
# set temp2_over 50
# set temp2_low 10
# Fans
# The CPU fan can be any of fan1, fan2 or fan3 - it's motherboard
# dependent. Same for the case fan.
label fan1 "CPU_PWM"
label fan2 "Rear "
ignore fan3
label vid "VID"
# ignore vid
# set fan1_min 2000
# set fan2_min 2000
# -------------------------------------------------------------------------------------------------
Både ACPI APIC support och Q_Fan är enablade i BIOS
Följde rekommendationerna hur man installerar lm_sensors och fick följande resultat (se nedan) som jag inte riktigt blir klok på.
Vad jag inte förstår är sensor utskriften:
- varför får man Core0/1 med 2 temp
- vad är CPU Temp (=+43°C ... jag har ju dual core system)
- varför går CPU fläkten så fort trots att core temp är låg
- vad är temp3
- hur får man bort dessa ALARM
- varför ör dokumentationen till lm_sensors & sensors.conf så dålig
Har kolla runt i olika forum men har kört fast ...
Tacksam för tips ...
/zkab
1) sensors ger:
k8temp-pci-00c3
Adapter: PCI adapter
Core0 Temp:
+24°C
Core0 Temp:
+22°C
Core1 Temp:
+20°C
Core1 Temp:
+24°C
it8716-isa-0290
Adapter: ISA adapter
VCore: +1.23 V (min = +0.00 V, max = +4.08 V)
3.3V: +3.25 V (min = +0.00 V, max = +4.08 V)
5V: +4.73 V (min = +0.00 V, max = +6.85 V)
12V: +11.65 V (min = +0.00 V, max = +16.32 V)
5VSB: +4.62 V (min = +0.00 V, max = +6.85 V)
VBat: +2.85 V
CPU_PWM: 1483 RPM (min = 3245 RPM) ALARM
Rear : 403 RPM (min = 3245 RPM) ALARM
CPU Temp: +43°C (low = -1°C, high = +127°C) sensor = diode
M/B Temp: +42°C (low = -1°C, high = +127°C) sensor = thermistor
Temp3: +25°C (low = -1°C, high = +127°C) sensor = thermistor
VID: +0.000 V
2) uname -a ger:
Linux 2.6.20-16-generic #2 SMP Wed May 23 01:46:23 UTC 2007 i686 GNU/Linux
3) cat /proc/cpuinfo ger:
processor : 0
vendor_id : AuthenticAMD
cpu family : 15
model : 107
model name : AMD Athlon(tm) 64 X2 Dual Core Processor 4800+
stepping : 1
cpu MHz : 2505.293
cache size : 512 KB
physical id : 0
siblings : 2
core id : 0
cpu cores : 2
fdiv_bug : no
hlt_bug : no
f00f_bug : no
coma_bug : no
fpu : yes
fpu_exception : yes
cpuid level : 1
wp : yes
flags : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat pse36 clflush mmx fxsr sse sse2 ht syscall nx mmxext fxsr_opt lm 3dnowext 3dnow pni cx16 lahf_lm cmp_legacy svm cr8legacy ts fid vid ttp tm stc [6]
bogomips : 5014.83
clflush size : 64
processor : 1
vendor_id : AuthenticAMD
cpu family : 15
model : 107
model name : AMD Athlon(tm) 64 X2 Dual Core Processor 4800+
stepping : 1
cpu MHz : 2505.293
cache size : 512 KB
physical id : 0
siblings : 2
core id : 1
cpu cores : 2
fdiv_bug : no
hlt_bug : no
f00f_bug : no
coma_bug : no
fpu : yes
fpu_exception : yes
cpuid level : 1
wp : yes
flags : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat pse36 clflush mmx fxsr sse sse2 ht syscall nx mmxext fxsr_opt lm 3dnowext 3dnow pni cx16 lahf_lm cmp_legacy svm cr8legacy ts fid vid ttp tm stc [6]
bogomips : 5010.80
clflush size : 64
4) /etc/sensors.config ser ut så här:
chip "it8716-*"
#---------------------------------------------------------------------- ZKAB
# Voltages
label in0 "VCore"
label in1 "3.3V"
label in3 "5V"
label in4 "12V"
label in7 "5VSB"
label in8 "VBat"
ignore in2
ignore in5
ignore in6
compute in3 ((6.8/10)+1)*@ , @/((6.8/10)+1)
compute in4 ((30/10)+1)*@ , @/((30/10)+1)
compute in7 ((6.8/10)+1)*@ , @/((6.8/10)+1)
# If vid (nominal CPU voltage) isn't correct, hardcode the correct value
# instead.
# set in0_min vid * 0.95
# set in0_max vid * 1.05
# set in2_min 3.3 * 0.95
# set in2_max 3.3 * 1.05
# set in3_min 5 * 0.95
# set in3_max 5 * 1.05
# set in4_min 12 * 0.95
# set in4_max 12 * 1.05
# set in7_min 5 * 0.95
# set in7_max 5 * 1.05
# The chip does not support in8 min/max
# Temperatures
# If you are lucky, the BIOS has set the proper sensor types for you.
# If your temperature readings are completely whacky you probably
# need to change the sensor types. Adujst and uncomment the
# appropriate lines below.
#
# 2 = thermistor; 3 = thermal diode; 0 = unused
# set sensor1 3
# set sensor2 3
# set sensor3 3
# If a given sensor isn't used, you will probably want to ignore it
# as well (see ignore statement right below).
# The CPU sensor can be any of temp1, temp2 or temp3 - it's motherboard
# dependent. Same for the motherboard temperature.
label temp1 "CPU Temp"
label temp2 "M/B Temp"
label temp3 "Temp3"
# ignore temp3
# set temp1_over 60
# set temp1_low 10
# set temp2_over 50
# set temp2_low 10
# Fans
# The CPU fan can be any of fan1, fan2 or fan3 - it's motherboard
# dependent. Same for the case fan.
label fan1 "CPU_PWM"
label fan2 "Rear "
ignore fan3
label vid "VID"
# ignore vid
# set fan1_min 2000
# set fan2_min 2000
# -------------------------------------------------------------------------------------------------