Jag precis köpt en projektor (panasonic pt-ax 200) som jag är jättenöjd med
Jag får fram bild till den genom gksudo nvidia-settings och kan där ställa in allt som jag önskar.
Problemet är att vid nästa uppstart så är allt bort och jag måste köra gksudo nvidia-settings, spara och köra ctrl-alt-backspace.
Varför sparas inte mina inställningar?
Personligen kan jag väl leva med det men frun är inte lika road av det.
Min xorg.conf ser ut så här just nu. Nu är projektorn igång och jag kör i i xinerama-läge.
Kod: Markera allt
# nvidia-settings: X configuration file generated by nvidia-settings
# nvidia-settings: version 1.0 (buildd@vernadsky) Thu Jun 5 09:26:53 UTC 2008
Section "ServerLayout"
Identifier "Layout0"
Screen 0 "Screen0" 0 0
Screen 1 "Screen1" RightOf "Screen0"
InputDevice "Keyboard0" "CoreKeyboard"
InputDevice "Mouse0" "CorePointer"
EndSection
Section "Files"
RgbPath "/usr/X11R6/lib/X11/rgb"
EndSection
Section "Module"
Load "dbe"
Load "extmod"
Load "type1"
Load "freetype"
Load "glx"
EndSection
Section "ServerFlags"
# Removed Option "Xinerama" "1"
# Removed Option "Xinerama" "0"
Option "Xinerama" "1"
EndSection
Section "InputDevice"
# generated from default
Identifier "Mouse0"
Driver "mouse"
Option "Protocol" "auto"
Option "Device" "/dev/psaux"
Option "Emulate3Buttons" "no"
Option "ZAxisMapping" "4 5"
EndSection
Section "InputDevice"
# generated from default
Identifier "Keyboard0"
Driver "kbd"
EndSection
Section "Monitor"
# HorizSync source: edid, VertRefresh source: edid
Identifier "Monitor0"
VendorName "Unknown"
ModelName "EIZO S1931"
HorizSync 31.0 - 64.0
VertRefresh 59.0 - 61.0
ModeLine "1280x960@60" 102.0 1280 1360 1496 1712 960 961 964 994 -hsync +vsync
ModeLine "1024x768@60" 65.0 1024 1048 1184 1344 768 771 777 806 -hsync -vsync
ModeLine "800x600@60" 40.0 800 840 968 1056 600 601 605 628 +hsync +vsync
ModeLine "640x480@60" 25.0 640 656 752 800 480 490 492 525 -hsync -vsync
Option "DPMS"
EndSection
Section "Monitor"
# HorizSync source: edid, VertRefresh source: edid
Identifier "Monitor1"
VendorName "Unknown"
ModelName "Panasonic AX-200"
HorizSync 28.0 - 68.0
VertRefresh 24.0 - 61.0
Option "DPMS"
EndSection
Section "Device"
Identifier "Videocard0"
Driver "nvidia"
VendorName "NVIDIA Corporation"
BoardName "GeForce 8600 GTS"
BusID "PCI:1:0:0"
Screen 0
EndSection
Section "Device"
Identifier "Videocard1"
Driver "nvidia"
VendorName "NVIDIA Corporation"
BoardName "GeForce 8600 GTS"
BusID "PCI:1:0:0"
Screen 1
EndSection
Section "Screen"
# Removed Option "TwinView" "0"
# Removed Option "metamodes" "DFP-0: nvidia-auto-select +0+0"
# Removed Option "TwinViewXineramaInfoOrder" "DFP-0"
# Removed Option "TwinViewXineramaInfoOrder" "DFP-1"
# Removed Option "TwinView" "1"
# Removed Option "metamodes" "DFP-0: nvidia-auto-select +0+0, DFP-1: nvidia-auto-select +1280+0"
Identifier "Screen0"
Device "Videocard0"
Monitor "Monitor0"
DefaultDepth 24
Option "TwinView" "0"
Option "TwinViewXineramaInfoOrder" "DFP-0"
Option "metamodes" "DFP-0: nvidia-auto-select +0+0"
SubSection "Display"
Depth 24
EndSubSection
EndSection
Section "Screen"
Identifier "Screen1"
Device "Videocard1"
Monitor "Monitor1"
DefaultDepth 24
Option "TwinView" "0"
Option "metamodes" "DFP-1: nvidia-auto-select +0+0"
SubSection "Display"
Depth 24
EndSubSection
EndSection
Tacksam för hjälp!