snabba upp saker o ting?

[Emka]

jag fattar ingenting nu, allt går verkligen långsamt här, trycker jag på något så tar det massor med tid inan det öppnas, ska jag in på hårdisken så vill jag inte att det tar 30 sek efter det att jag klickat på den.

ett annat exempel är när jag skulle öppna en .rar fil på lite över 3 gig, tog en halvimme att öppna och ytterliggare en halvtimme att bränna ut den, skall det verkligen gå så segt?

vad kan man göra för att snabba upp skiten lite? blir galen på att det inte går som jag vill 

har 1 gig i ram så det skall ju klara att surfa och öppna en mapp samtidigt utan väntetider...

nån som har ett förslag?

[Sork]

hmmm låter ju lite konstigt. kan du beskriva din hårdvara lite mer ingående. processor etc

[mcNisse]

Starta ett program som kollar vilka processer som körs och drar mycket kraft, tex top i en terminal. Det kan ge indikation på vad som är fel.

[rewz]

Jag har haft liknande problem...

Om du sitter i fiesty vill jag börja med att rekommendera en uppgradering till Gusty,
Detta fixade (för mig) problemet med slö uppackning. Sen vill jag också nämna att om du
packar upp ifrån eller till NTFS partitioner går det mycket slöare än ext3...

När det gäller bränningen så tog det precis som för dig ca 30min att bränna en DVD.
Ända lösningen som funkade för mig var att installera NERO har testat med flera olika
brännarprogram men som sagt det ända som funkat är NERO.
Vill också tillägga att jag inte testat något annat program än NERO sen jag uppgraderade till
Gusty. 

[Emka]

hmmm låter ju lite konstigt. kan du beskriva din hårdvara lite mer ingående. processor etc

jag vet faktiskt inte vad det är jag har 

det är ett bygge jag fick överta när polaren skaffade sig en ny burk, finns det nåt program man kan använda för att kolla vad som finns i burken? som nåt liknande everest som finns till MS...

Starta ett program som kollar vilka processer som körs och drar mycket kraft, tex top i en terminal. Det kan ge indikation på vad som är fel.

förklara gärna lite mer ingånde, tänk på att jag är trög 

jag fattar inte vad felet är, jag skall flytta en mapp på kanske 700mb, det tar MINST en kvart! öppna nånting med totem tar iallafall 30-40 sek innan det öppnas... 

flyttade över en mapp till min externa på ca 45 gig, tog nästan två timmar!

jag har gutsy nu.

[Jimbo]

hmmm låter ju lite konstigt. kan du beskriva din hårdvara lite mer ingående. processor etc

jag vet faktiskt inte vad det är jag har 

det är ett bygge jag fick överta när polaren skaffade sig en ny burk, finns det nåt program man kan använda för att kolla vad som finns i burken? som nåt liknande everest som finns till MS...

Jag är ganska nybörjare men vad jag förstått går det att få fram det mesta om den hårdvaran som sitter i datorn genom att skriva kommandot "dmesg" i terminalen. Fungerar inte det testa "sudo dmesg".

Det är ganska mycket information så det gäller att veta vad man letar efter.
För att underlätta lite kan man skriva t.ex. "dmesg | grep CPU" för att bara få fram de rader som hanterar vilken processor som i datorn.

Starta ett program som kollar vilka processer som körs och drar mycket kraft, tex top i en terminal. Det kan ge indikation på vad som är fel.

förklara gärna lite mer ingånde, tänk på att jag är trög 

jag fattar inte vad felet är, jag skall flytta en mapp på kanske 700mb, det tar MINST en kvart! öppna nånting med totem tar iallafall 30-40 sek innan det öppnas... 

flyttade över en mapp till min externa på ca 45 gig, tog nästan två timmar!

jag har gutsy nu.

Gör så att du startar ett nytt terminalfönster, i det terminalfönstret skriver du in kommandot "top".
Med det kommandot startar du ett program som övervakar alla processer i ditt system.
Fokusera på den 8:e kolumnen %CPU, här visas hur mycket av din processor som varje process använder.
Finns det någon process som tar upp många %? Om inte, lämna terminalen öppen och testa starta något program och se vad som händer.
För att avsluta top är det bara att trycka på 'q'

Hoppas jag har hjälpt dig lite, om inte, fråga på 

[Emka]

[    0.000000] Linux version 2.6.22-14-generic (buildd@palmer) (gcc version 4.1.3 20070929 (prerelease) (Ubuntu 4.1.2-16ubuntu2)) #1 SMP Sun Oct 14 23:05:12 GMT 2007 (Ubuntu 2.6.22-14.46-generic)
[    0.000000] BIOS-provided physical RAM map:
[    0.000000]  BIOS-e820: 0000000000000000 - 000000000009f800 (usable)
[    0.000000]  BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved)
[    0.000000]  BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
[    0.000000]  BIOS-e820: 0000000000100000 - 000000003fff0000 (usable)
[    0.000000]  BIOS-e820: 000000003fff0000 - 000000003fff3000 (ACPI NVS)
[    0.000000]  BIOS-e820: 000000003fff3000 - 0000000040000000 (ACPI data)
[    0.000000]  BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
[    0.000000]  BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
[    0.000000]  BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
[    0.000000] 127MB HIGHMEM available.
[    0.000000] 896MB LOWMEM available.
[    0.000000] Entering add_active_range(0, 0, 262128) 0 entries of 256 used
[    0.000000] Zone PFN ranges:
[    0.000000]  DMA            0 ->    4096
[    0.000000]  Normal      4096 ->  229376
[    0.000000]  HighMem    229376 ->  262128
[    0.000000] early_node_map[1] active PFN ranges
[    0.000000]    0:        0 ->  262128
[    0.000000] On node 0 totalpages: 262128
[    0.000000]  DMA zone: 32 pages used for memmap
[    0.000000]  DMA zone: 0 pages reserved
[    0.000000]  DMA zone: 4064 pages, LIFO batch:0
[    0.000000]  Normal zone: 1760 pages used for memmap
[    0.000000]  Normal zone: 223520 pages, LIFO batch:31
[    0.000000]  HighMem zone: 255 pages used for memmap
[    0.000000]  HighMem zone: 32497 pages, LIFO batch:7
[    0.000000] DMI 2.2 present.
[    0.000000] ACPI: RSDP signature @ 0xC00F7A20 checksum 0
[    0.000000] ACPI: RSDP 000F7A20, 0014 (r0 Nvidia)
[    0.000000] ACPI: RSDT 3FFF3000, 002C (r1 Nvidia AWRDACPI 42302E31 AWRD        0)
[    0.000000] ACPI: FACP 3FFF3040, 0074 (r1 Nvidia AWRDACPI 42302E31 AWRD        0)
[    0.000000] ACPI: DSDT 3FFF30C0, 523F (r1 NVIDIA AWRDACPI    1000 MSFT  100000E)
[    0.000000] ACPI: FACS 3FFF0000, 0040
[    0.000000] ACPI: APIC 3FFF8300, 006E (r1 Nvidia AWRDACPI 42302E31 AWRD        0)
[    0.000000] Nvidia board detected. Ignoring ACPI timer override.
[    0.000000] If you got timer trouble try acpi_use_timer_override
[    0.000000] ACPI: PM-Timer IO Port: 0x4008
[    0.000000] ACPI: Local APIC address 0xfee00000
[    0.000000] ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
[    0.000000] Processor #0 6:8 APIC version 16
[    0.000000] ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
[    0.000000] ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
[    0.000000] IOAPIC[0]: apic_id 2, version 17, address 0xfec00000, GSI 0-23
[    0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[    0.000000] ACPI: BIOS IRQ0 pin2 override ignored.
[    0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[    0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 14 global_irq 14 high edge)
[    0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 15 global_irq 15 high edge)
[    0.000000] ACPI: IRQ9 used by override.
[    0.000000] ACPI: IRQ14 used by override.
[    0.000000] ACPI: IRQ15 used by override.
[    0.000000] Enabling APIC mode:  Flat.  Using 1 I/O APICs
[    0.000000] Using ACPI (MADT) for SMP configuration information
[    0.000000] Allocating PCI resources starting at 50000000 (gap: 40000000:bec00000)
[    0.000000] Built 1 zonelists.  Total pages: 260081
[    0.000000] Kernel command line: root=UUID=ef75a8cb-f341-4cf8-a44c-634c97656b18 ro quiet splash locale=sv_SE
[    0.000000] mapped APIC to ffffd000 (fee00000)
[    0.000000] mapped IOAPIC to ffffc000 (fec00000)
[    0.000000] Enabling fast FPU save and restore... done.
[    0.000000] Enabling unmasked SIMD FPU exception support... done.
[    0.000000] Initializing CPU#0
[    0.000000] PID hash table entries: 4096 (order: 12, 16384 bytes)
[    0.000000] Detected 1733.355 MHz processor.
[  17.373970] Console: colour VGA+ 80x25
[  17.374721] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[  17.375957] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[  17.410803] Memory: 1027752k/1048512k available (2015k kernel code, 19988k reserved, 916k data, 364k init, 131008k highmem)
[  17.410815] virtual kernel memory layout:
[  17.410817]    fixmap  : 0xfff4d000 - 0xfffff000  ( 712 kB)
[  17.410818]    pkmap  : 0xff800000 - 0xffc00000  (4096 kB)
[  17.410820]    vmalloc : 0xf8800000 - 0xff7fe000  ( 111 MB)
[  17.410821]    lowmem  : 0xc0000000 - 0xf8000000  ( 896 MB)
[  17.410823]      .init : 0xc03e3000 - 0xc043e000  ( 364 kB)
[  17.410824]      .data : 0xc02f7d26 - 0xc03dce84  ( 916 kB)
[  17.410826]      .text : 0xc0100000 - 0xc02f7d26  (2015 kB)
[  17.410830] Checking if this processor honours the WP bit even in supervisor mode... Ok.
[  17.410888] SLUB: Genslabs=22, HWalign=32, Order=0-1, MinObjects=4, CPUs=1, Nodes=1
[  17.490813] Calibrating delay using timer specific routine.. 3469.59 BogoMIPS (lpj=6939182)
[  17.490857] Security Framework v1.0.0 initialized
[  17.490868] SELinux:  Disabled at boot.
[  17.490888] Mount-cache hash table entries: 512
[  17.491082] CPU: After generic identify, caps: 0383fbff c1c3fbff 00000000 00000000 00000000 00000000 00000000
[  17.491095] CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
[  17.491098] CPU: L2 Cache: 256K (64 bytes/line)
[  17.491102] CPU: After all inits, caps: 0383fbff c1c3fbff 00000000 00000420 00000000 00000000 00000000
[  17.491116] Compat vDSO mapped to ffffe000.
[  17.491133] Checking 'hlt' instruction... OK.
[  17.506984] SMP alternatives: switching to UP code
[  17.507337] Freeing SMP alternatives: 11k freed
[  17.507770] Early unpacking initramfs... done
[  17.867939] ACPI: Core revision 20070126
[  17.868060] ACPI: Looking for DSDT in initramfs... error, file /DSDT.aml not found.
[  17.882923] CPU0: AMD Athlon(tm) XP 2100+ stepping 01
[  17.882951] Total of 1 processors activated (3469.59 BogoMIPS).
[  17.883154] ENABLING IO-APIC IRQs
[  17.883345] ..TIMER: vector=0x31 apic1=0 pin1=0 apic2=-1 pin2=-1
[  18.030215] Brought up 1 CPUs
[  18.030375] Booting paravirtualized kernel on bare hardware
[  18.030451] Time:  1:17:48  Date: 10/10/107
[  18.030489] NET: Registered protocol family 16
[  18.030612] EISA bus registered
[  18.030626] ACPI: bus type pci registered
[  18.062976] PCI: PCI BIOS revision 2.10 entry at 0xfbb70, last bus=2
[  18.062979] PCI: Using configuration type 1
[  18.062981] Setting up standard PCI resources
[  18.068234] ACPI: EC: Look up EC in DSDT
[  18.074657] ACPI: Interpreter enabled
[  18.074661] ACPI: (supports S0 S1 S4 S5)
[  18.074680] ACPI: Using IOAPIC for interrupt routing
[  18.086643] ACPI: PCI Root Bridge [PCI0] (0000:00)
[  18.086653] PCI: Probing PCI hardware (bus 00)
[  18.087632] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[  18.087862] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.HUB0._PRT]
[  18.088189] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.AGPB._PRT]
[  18.144386] ACPI: PCI Interrupt Link [LNK1] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
[  18.144602] ACPI: PCI Interrupt Link [LNK2] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
[  18.144815] ACPI: PCI Interrupt Link [LNK3] (IRQs 3 4 5 6 7 9 10 *11 12 14 15)
[  18.145026] ACPI: PCI Interrupt Link [LNK4] (IRQs 3 4 5 6 7 9 *10 11 12 14 15)
[  18.145234] ACPI: PCI Interrupt Link [LNK5] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
[  18.145444] ACPI: PCI Interrupt Link [LUBA] (IRQs 3 4 5 6 7 9 10 *11 12 14 15)
[  18.145662] ACPI: PCI Interrupt Link [LUBB] (IRQs 3 4 5 6 7 *9 10 11 12 14 15)
[  18.145871] ACPI: PCI Interrupt Link [LMAC] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
[  18.146102] ACPI: PCI Interrupt Link [LAPU] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
[  18.146317] ACPI: PCI Interrupt Link [LACI] (IRQs 3 4 *5 6 7 9 10 11 12 14 15)
[  18.146531] ACPI: PCI Interrupt Link [LMCI] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
[  18.146743] ACPI: PCI Interrupt Link [LSMB] (IRQs 3 4 5 6 7 9 *10 11 12 14 15)
[  18.146956] ACPI: PCI Interrupt Link [LUB2] (IRQs *3 4 5 6 7 9 10 11 12 14 15)
[  18.147168] ACPI: PCI Interrupt Link [LFIR] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
[  18.147379] ACPI: PCI Interrupt Link [L3CM] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
[  18.147589] ACPI: PCI Interrupt Link [liDE] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
[  18.147809] ACPI: PCI Interrupt Link [LSID] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
[  18.147990] ACPI: PCI Interrupt Link [APC1] (IRQs *16), disabled.
[  18.148153] ACPI: PCI Interrupt Link [APC2] (IRQs *17), disabled.
[  18.148314] ACPI: PCI Interrupt Link [APC3] (IRQs *18)
[  18.148474] ACPI: PCI Interrupt Link [APC4] (IRQs *19)
[  18.148634] ACPI: PCI Interrupt Link [APC5] (IRQs *16), disabled.
[  18.148865] ACPI: PCI Interrupt Link [APCF] (IRQs 20 21) *0
[  18.149094] ACPI: PCI Interrupt Link [APCG] (IRQs 20 21) *0
[  18.149321] ACPI: PCI Interrupt Link [APCH] (IRQs 20 21) *0, disabled.
[  18.149548] ACPI: PCI Interrupt Link [APCI] (IRQs 20 21) *0, disabled.
[  18.149775] ACPI: PCI Interrupt Link [APCJ] (IRQs 20 21) *0
[  18.150001] ACPI: PCI Interrupt Link [APCK] (IRQs 20 21) *0, disabled.
[  18.150170] ACPI: PCI Interrupt Link [APCS] (IRQs *23)
[  18.150398] ACPI: PCI Interrupt Link [APCL] (IRQs 20 21) *0
[  18.150627] ACPI: PCI Interrupt Link [APCM] (IRQs 20 21) *0, disabled.
[  18.150855] ACPI: PCI Interrupt Link [AP3C] (IRQs 20 21) *0, disabled.
[  18.151083] ACPI: PCI Interrupt Link [APCZ] (IRQs 20 21) *0, disabled.
[  18.151321] ACPI: PCI Interrupt Link [APSI] (IRQs 22) *0, disabled.
[  18.151516] ACPI: Power Resource [ISAV] (on)
[  18.151543] Linux Plug and Play Support v0.97 (c) Adam Belay
[  18.151560] pnp: PnP ACPI init
[  18.151575] ACPI: bus type pnp registered
[  18.157186] pnp: PnP ACPI: found 14 devices
[  18.157190] ACPI: ACPI bus type pnp unregistered
[  18.157196] PnPBIOS: Disabled by ACPI PNP
[  18.157264] PCI: Using ACPI for IRQ routing
[  18.157270] PCI: If a device doesn't work, try "pci=routeirq".  If it helps, post a report
[  18.204126] NET: Registered protocol family 8
[  18.204128] NET: Registered protocol family 20
[  18.204222] pnp: 00:00: ioport range 0x4000-0x407f has been reserved
[  18.204226] pnp: 00:00: ioport range 0x4080-0x40ff has been reserved
[  18.204230] pnp: 00:00: ioport range 0x4400-0x447f has been reserved
[  18.204233] pnp: 00:00: ioport range 0x4480-0x44ff has been reserved
[  18.204236] pnp: 00:00: ioport range 0x4200-0x427f has been reserved
[  18.204239] pnp: 00:00: ioport range 0x4280-0x42ff has been reserved
[  18.204246] pnp: 00:01: ioport range 0x5000-0x503f has been reserved
[  18.204249] pnp: 00:01: ioport range 0x5100-0x513f has been reserved
[  18.204257] pnp: 00:02: iomem range 0xd1000-0xd3fff has been reserved
[  18.204260] pnp: 00:02: iomem range 0xf0000-0xf7fff could not be reserved
[  18.204264] pnp: 00:02: iomem range 0xf8000-0xfbfff could not be reserved
[  18.204267] pnp: 00:02: iomem range 0xfc000-0xfffff could not be reserved
[  18.205946] Time: tsc clocksource has been installed.
[  18.234629] PCI: Bridge: 0000:00:08.0
.........................................................................

fortsättning nedan

[Emka]

forts:
[  18.234633]  IO window: c000-cfff
[  18.234639]  MEM window: eb000000-ebffffff
[  18.234643]  PREFETCH window: disabled.
[  18.234651] PCI: Bridge: 0000:00:1e.0
[  18.234652]  IO window: disabled.
[  18.234657]  MEM window: e8000000-eaffffff
[  18.234661]  PREFETCH window: d0000000-dfffffff
[  18.234674] PCI: Setting latency timer of device 0000:00:08.0 to 64
[  18.234692] NET: Registered protocol family 2
[  18.273929] IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
[  18.274156] TCP established hash table entries: 131072 (order: 8, 1572864 bytes)
[  18.276735] TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
[  18.277633] TCP: Hash tables configured (established 131072 bind 65536)
[  18.277639] TCP reno registered
[  18.286024] checking if image is initramfs... it is
[  18.737310] Switched to high resolution mode on CPU 0
[  18.969085] Freeing initrd memory: 7120k freed
[  18.969638] audit: initializing netlink socket (disabled)
[  18.969656] audit(1194657468.184:1): initialized
[  18.969742] highmem bounce pool size: 64 pages
[  18.971931] VFS: Disk quotas dquot_6.5.1
[  18.971997] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[  18.972123] io scheduler noop registered
[  18.972126] io scheduler anticipatory registered
[  18.972129] io scheduler deadline registered
[  18.972144] io scheduler cfq registered (default)
[  18.972200] Boot video device is 0000:02:00.0
[  18.972430] isapnp: Scanning for PnP cards...
[  19.326563] isapnp: No Plug & Play device found
[  19.367927] Real Time Clock Driver v1.12ac
[  19.368070] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
[  19.368188] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[  19.369478] 00:0a: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[  19.370473] RAMDISK driver initialized: 16 RAM disks of 65536K size 1024 blocksize
[  19.370753] input: Macintosh mouse button emulation as /class/input/input0
[  19.370860] PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
[  19.374123] serio: i8042 KBD port at 0x60,0x64 irq 1
[  19.374133] serio: i8042 AUX port at 0x60,0x64 irq 12
[  19.374402] mice: PS/2 mouse device common for all mice
[  19.374559] EISA: Probing bus 0 at eisa.0
[  19.374585] Cannot allocate resource for EISA slot 4
[  19.374588] Cannot allocate resource for EISA slot 5
[  19.374604] EISA: Detected 0 cards.
[  19.374734] TCP cubic registered
[  19.374745] NET: Registered protocol family 1
[  19.374772] Using IPI No-Shortcut mode
[  19.375001]  Magic number: 15:602:255
[  19.375086]  hash matches device ttyte
[  19.375793] Freeing unused kernel memory: 364k freed
[  19.408407] input: AT Translated Set 2 keyboard as /class/input/input1
[  20.640691] AppArmor: AppArmor initialized<5>audit(1194657469.684:2):  type=1505 info="AppArmor initialized" pid=1234
[  20.648833] fuse init (API version 7.
[  20.655045] Failure registering capabilities with primary security module.
[  20.675167] ACPI: Fan [FAN] (on)
[  20.683046] ACPI: Thermal Zone [THRM] (56 C)
[  21.488537] usbcore: registered new interface driver usbfs
[  21.488574] usbcore: registered new interface driver hub
[  21.488605] usbcore: registered new device driver usb
[  21.489621] ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver
[  21.490120] ACPI: PCI Interrupt Link [APCF] enabled at IRQ 21
[  21.490131] ACPI: PCI Interrupt 0000:00:02.0[A] -> Link [APCF] -> GSI 21 (level, high) -> IRQ 16
[  21.490148] PCI: Setting latency timer of device 0000:00:02.0 to 64
[  21.490152] ohci_hcd 0000:00:02.0: OHCI Host Controller
[  21.490446] ohci_hcd 0000:00:02.0: new USB bus registered, assigned bus number 1
[  21.490473] ohci_hcd 0000:00:02.0: irq 16, io mem 0xec003000
[  21.551325] SCSI subsystem initialized
[  21.557353] libata version 2.21 loaded.
[  21.604269] usb usb1: configuration #1 chosen from 1 choice
[  21.604310] hub 1-0:1.0: USB hub found
[  21.604326] hub 1-0:1.0: 4 ports detected
[  21.705902] ACPI: PCI Interrupt Link [APCG] enabled at IRQ 20
[  21.705916] ACPI: PCI Interrupt 0000:00:02.1 -> Link [APCG] -> GSI 20 (level, high) -> IRQ 17
[  21.705936] PCI: Setting latency timer of device 0000:00:02.1 to 64
[  21.705941] ohci_hcd 0000:00:02.1: OHCI Host Controller
[  21.705976] ohci_hcd 0000:00:02.1: new USB bus registered, assigned bus number 2
[  21.706000] ohci_hcd 0000:00:02.1: irq 17, io mem 0xec004000
[  21.721277] Floppy drive(s): fd0 is 1.44M
[  21.763347] usb usb2: configuration #1 chosen from 1 choice
[  21.763384] hub 2-0:1.0: USB hub found
[  21.763400] hub 2-0:1.0: 4 ports detected
[  21.778272] FDC 0 is a post-1991 82077
[  21.865743] ACPI: PCI Interrupt Link [APCL] enabled at IRQ 21
[  21.865751] ACPI: PCI Interrupt 0000:00:02.2[C] -> Link [APCL] -> GSI 21 (level, high) -> IRQ 16
[  21.865768] PCI: Setting latency timer of device 0000:00:02.2 to 64
[  21.865773] ehci_hcd 0000:00:02.2: EHCI Host Controller
[  21.865819] ehci_hcd 0000:00:02.2: new USB bus registered, assigned bus number 3
[  21.865868] ehci_hcd 0000:00:02.2: debug port 1
[  21.865874] PCI: cache line size of 64 is not supported by device 0000:00:02.2
[  21.865884] ehci_hcd 0000:00:02.2: irq 16, io mem 0xec005000
[  22.008832] usb 1-2: new full speed USB device using ohci_hcd and address 2
[  22.008866] ehci_hcd 0000:00:02.2: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
[  22.009013] usb usb3: configuration #1 chosen from 1 choice
[  22.009050] hub 3-0:1.0: USB hub found
[  22.009063] hub 3-0:1.0: 8 ports detected
[  22.118481] Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
[  22.118489] ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
[  22.119415] NFORCE2-U400R: IDE controller at PCI slot 0000:00:09.0
[  22.119570] NFORCE2-U400R: chipset revision 163
[  22.119573] NFORCE2-U400R: not 100% native mode: will probe irqs later
[  22.119579] NFORCE2-U400R: BIOS didn't set cable bits correctly. Enabling workaround.
[  22.119582] NFORCE2-U400R: BIOS didn't set cable bits correctly. Enabling workaround.
[  22.119589] NFORCE2-U400R: 0000:00:09.0 (rev a3) UDMA133 controller
[  22.119602]    ide0: BM-DMA at 0xf000-0xf007, BIOS settings: hda:DMA, hdb:DMA
[  22.119617]    ide1: BM-DMA at 0xf008-0xf00f, BIOS settings: hdc:DMA, hdd:DMA
[  22.119628] Probing IDE interface ide0...
[  22.404406] hda: SAMSUNG SV0813H, ATA DISK drive
[  22.684030] hdb: SAMSUNG SV1204H, ATA DISK drive
[  22.740122] ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
[  22.755086] Probing IDE interface ide1...
[  22.803749] usb 3-6: new high speed USB device using ehci_hcd and address 3
[  22.936905] usb 3-6: configuration #1 chosen from 1 choice
[  23.155395] hdc: _NEC DVD_RW ND-3520A, ATAPI CD/DVD-ROM drive
[  23.239168] usb 1-2: new full speed USB device using ohci_hcd and address 3
[  23.435022] hdd: SAMSUNG SV1203N, ATA DISK drive
[  23.451828] usb 1-2: configuration #1 chosen from 1 choice
[  23.456633] usbcore: registered new interface driver libusual
[  23.461908] Initializing USB Mass Storage driver...
[  23.462114] scsi0 : SCSI emulation for USB Mass Storage devices
[  23.462174] usb-storage: device found at 3
[  23.462176] usb-storage: waiting for device to settle before scanning
[  23.462203] usbcore: registered new interface driver usb-storage
[  23.462206] USB Mass Storage support registered.
[  23.491294] ide1 at 0x170-0x177,0x376 on irq 15
[  23.494975] VIA Networking Velocity Family Gigabit Ethernet Adapter Driver Ver. 1.14
[  23.494978] Copyright (c) 2002, 2003 VIA Networking Technologies, Inc.
[  23.494981] Copyright (c) 2004 Red Hat Inc.
[  23.495255] ACPI: PCI Interrupt Link [APC3] enabled at IRQ 18
[  23.495267] ACPI: PCI Interrupt 0000:01:0b.0[A] -> Link [APC3] -> GSI 18 (level, low) -> IRQ 18
[  23.495998] eth0: VIA Networking Velocity Family Gigabit Ethernet Adapter
[  23.496003] eth0: Ethernet Address: 00:50:8D:61:BD:3F
[  23.505553] hda: max request size: 128KiB
[  23.526746] hda: 156368016 sectors (80060 MB) w/2048KiB Cache, CHS=65535/16/63, UDMA(100)
[  23.527598] hda: cache flushes supported
[  23.527676]  hda: hda1 hda2 < hda5 >
[  23.557340] hdb: max request size: 128KiB
[  23.557426] hdb: 234493056 sectors (120060 MB) w/2048KiB Cache, CHS=65535/16/63, UDMA(100)
[  23.557496] hdb: cache flushes supported
[  23.557541]  hdb: hdb1
[  23.565384] hdd: max request size: 512KiB
[  23.565457] hdd: 234493056 sectors (120060 MB) w/2048KiB Cache, CHS=16383/255/63, UDMA(100)
[  23.565670] hdd: cache flushes supported
[  23.565703]  hdd: hdd1
[  23.607095] hdc: ATAPI 48X DVD-ROM DVD-R CD-R/RW drive, 2048kB Cache, UDMA(33)
[  23.607108] Uniform CD-ROM driver Revision: 3.20
[  24.176370] Attempting manual resume
[  24.176375] swsusp: Resume From Partition 3:5
[  24.176377] PM: Checking swsusp image.
[  24.176629] PM: Resume from disk failed.
[  24.217441] kjournald starting.  Commit interval 5 seconds
[  24.217458] EXT3-fs: mounted filesystem with ordered data mode.
[  28.452312] usb-storage: device scan complete
[  28.453177] scsi 0:0:0:0: Direct-Access    EPSON    Stylus Storage  1.00 PQ: 0 ANSI: 2
[  42.394434] Linux agpgart interface v0.102 (c) Dave Jones
[  42.448287] agpgart: Detected NVIDIA nForce2 chipset
[  42.459194] agpgart: AGP aperture is 128M @ 0xe0000000
[  42.635091] i2c-adapter i2c-0: nForce2 SMBus adapter at 0x5000
[  42.635161] i2c-adapter i2c-1: nForce2 SMBus adapter at 0x5100
[  43.029136] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[  43.033259] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[  43.959615] /build/buildd/linux-source-2.6.22-2.6.22/drivers/usb/class/usblp.c: usblp0: USB Bidirectional printer dev 3 if 1 alt 0 proto 2 vid 0x04B8 pid 0x0803
[  43.959642] usbcore: registered new interface driver usblp
[  43.959646] /build/buildd/linux-source-2.6.22-2.6.22/drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
[  44.109612] gameport: EMU10K1 is pci0000:01:06.1/gameport0, io 0xc400, speed 59659kHz
[  44.130698] Linux video capture interface: v2.00
[  44.164728] logips2pp: Detected unknown logitech mouse model 127
[  44.282997] sd 0:0:0:0: [sda] Attached SCSI removable disk
[  44.382447] input: PC Speaker as /class/input/input2
[  44.572710] /build/buildd/linux-ubuntu-modules-2.6.22-2.6.22/debian/build/build-generic/media/gspcav1/gspca_core.c: USB SPCA5XX camera found. (PAC207)
[  44.584285] usbcore: registered new interface driver gspca
[  44.584293] /build/buildd/linux-ubuntu-modules-2.6.22-2.6.22/debian/build/build-generic/media/gspcav1/gspca_core.c: gspca driver 01.00.12 registered
[  44.634437] input: ImExPS/2 Logitech Explorer Mouse as /class/input/input3
[  44.637022] parport_pc 00:0b: reported by Plug and Play ACPI
[  44.637148] parport0: PC-style at 0x378 (0x778), irq 7, dma 3 [PCSPP,TRISTATE,COMPAT,EPP,ECP,DMA]
[  44.669543] sd 0:0:0:0: Attached scsi generic sg0 type 0
[  44.812016] nvidia: module license 'NVIDIA' taints kernel.
[  45.066853] ACPI: PCI Interrupt Link [APC4] enabled at IRQ 19
[  45.066867] ACPI: PCI Interrupt 0000:02:00.0[A] -> Link [APC4] -> GSI 19 (level, low) -> IRQ 19
[  45.067417] NVRM: loading NVIDIA UNIX x86 Kernel Module  100.14.19  Wed Sep 12 14:12:24 PDT 2007
[  45.365948] ACPI: PCI Interrupt 0000:01:06.0[A] -> Link [APC3] -> GSI 18 (level, low) -> IRQ 18
[  45.402150] ACPI: PCI Interrupt Link [APCJ] enabled at IRQ 20
[  45.402159] ACPI: PCI Interrupt 0000:00:06.0[A] -> Link [APCJ] -> GSI 20 (level, high) -> IRQ 17
[  45.402202] PCI: Setting latency timer of device 0000:00:06.0 to 64
[  45.724833] intel8x0_measure_ac97_clock: measured 53711 usecs
[  45.724839] intel8x0: clocking to 47450
[  46.634477] lp0: using parport0 (interrupt-driven).
[  46.706066] Adding 3028212k swap on /dev/hda5.  Priority:-1 extents:1 across:3028212k
[  47.112804] EXT3 FS on hda1, internal journal
[  49.263695] No dock devices found.
[  49.575313] input: Power Button (FF) as /class/input/input4
[  49.581456] ACPI: Power Button (FF) [PWRF]
[  49.625298] input: Power Button (CM) as /class/input/input5
[  49.631429] ACPI: Power Button (CM) [PWRB]
[  52.614048] Velocity is AUTO mode
[  54.279989] eth0: Link auto-negotiation speed 100M bps full duplex
[  56.357884] ppdev: user-space parallel port driver
[  60.048472] audit(1194657510.195:3):  type=1503 operation="inode_permission" requested_mask="a" denied_mask="a" name="/dev/tty" pid=5184 profile="/usr/sbin/cupsd"
[  60.581628] agpgart: Found an AGP 3.0 compliant device at 0000:00:00.0.
[  60.581648] agpgart: Putting AGP V3 device at 0000:00:00.0 into 8x mode
[  60.581709] agpgart: Putting AGP V3 device at 0000:02:00.0 into 8x mode
[  61.358405] apm: BIOS version 1.2 Flags 0x07 (Driver version 1.16ac)
[  61.358410] apm: overridden by ACPI.
[  66.420555] Failure registering capabilities with primary security module.
[  67.176939] Bluetooth: Core ver 2.11
[  67.177097] NET: Registered protocol family 31
[  67.177100] Bluetooth: HCI device and connection manager initialized
[  67.177105] Bluetooth: HCI socket layer initialized
[  67.212005] Bluetooth: L2CAP ver 2.8
[  67.212012] Bluetooth: L2CAP socket layer initialized
[  67.246946] Bluetooth: RFCOMM socket layer initialized
[  67.247055] Bluetooth: RFCOMM TTY layer initialized
[  67.247058] Bluetooth: RFCOMM ver 1.8
[  72.501970] NET: Registered protocol family 17
[  77.563801] NET: Registered protocol family 10
[  77.564038] lo: Disabled Privacy Extensions
[  88.407272] eth0: no IPv6 routers present
[  111.160737] /build/buildd/linux-source-2.6.22-2.6.22/drivers/usb/class/usblp.c: usblp0: off-line
[  509.799269] /build/buildd/linux-source-2.6.22-2.6.22/drivers/usb/class/usblp.c: usblp0: off-line
[16806.966219] agpgart: Found an AGP 3.0 compliant device at 0000:00:00.0.
[16806.966241] agpgart: Putting AGP V3 device at 0000:00:00.0 into 8x mode
[16806.966302] agpgart: Putting AGP V3 device at 0000:02:00.0 into 8x mode
[52508.470598] kjournald starting.  Commit interval 5 seconds
[52508.470986] EXT3-fs warning: maximal mount count reached, running e2fsck is recommended
[52508.477563] EXT3 FS on hdd1, internal journal
[52508.477861] EXT3-fs: mounted filesystem with ordered data mode.
[52511.103326] kjournald starting.  Commit interval 5 seconds
[52511.103713] EXT3-fs warning: maximal mount count reached, running e2fsck is recommended
[52511.110215] EXT3 FS on hdb1, internal journal
[52511.110445] EXT3-fs: mounted filesystem with ordered data mode.

[Emka]

i "top" får jag fram:

top - 17:10:25 up 14:53,  2 users,  load average: 1.86, 1.75, 1.34
Tasks: 109 total,  4 running, 105 sleeping,  0 stopped,  0 zombie
Cpu(s): 30.5%us,  8.3%sy,  0.0%ni, 51.0%id,  5.3%wa,  1.7%hi,  3.3%si,  0.0%st
Mem:  1035636k total,  1017048k used,    18588k free,    14784k buffers
Swap:  3028212k total,    34740k used,  2993472k free,  617468k cached

  PID USER      PR  NI  VIRT  RES  SHR S %CPU %MEM    TIME+  COMMAND         
8565 emil      16  0  418m 104m  21m S 13.0 10.3  3:44.36 java           
7898 root      15  0 60596  48m 9.8m S 11.3  4.8  1:22.02 Xorg           
8518 emil      15  0  218m  70m  22m R  9.7  7.0  1:55.79 firefox-bin     
8339 emil      15  0 76908  26m  15m S  2.3  2.6  0:04.79 gnome-panel     
8336 emil      15  0 18696  10m 7740 R  1.7  1.0  0:05.16 metacity       
8392 emil      15  0 16868 2748 1768 S  1.3  0.3  0:02.53 gnome-screensav 
8997 emil      15  0 83588  18m  10m R  1.0  1.8  0:03.66 gnome-terminal 
8683 root      10  -5    0    0    0 S  0.3  0.0  0:01.88 kjournald       
9056 emil      15  0  2364 1144  876 R  0.3  0.1  0:00.71 top             
    1 root      18  0  2948 1856  532 S  0.0  0.2  0:01.38 init           
    2 root      11  -5    0    0    0 S  0.0  0.0  0:00.00 kthreadd       
    3 root      RT  -5    0    0    0 S  0.0  0.0  0:00.00 migration/0     
    4 root      34  19    0    0    0 S  0.0  0.0  0:00.07 ksoftirqd/0     
    5 root      RT  -5    0    0    0 S  0.0  0.0  0:00.00 watchdog/0     
    6 root      10  -5    0    0    0 S  0.0  0.0  0:00.04 events/0       
    7 root      10  -5    0    0    0 S  0.0  0.0  0:00.00 khelper         
  26 root      10  -5    0    0    0 S  0.0  0.0  0:00.03 kblockd/0       



nån som har förslag?

[Emka]

ingen?

[Jimbo]

All information från dmesg kanske var att ta i lite

Du verkar ha en AMD Athlon XP 2100+ och ett grafikkort med 128MB RAM, din hdd är en SAMSUNG SV1203N, ATA.
Från den informationen som dmesg visar verkar du ha en bra dator.

Men informationen från top är lite sämre, det verkar som om 30% av din processor används vid idle.
Men "load average: 1.86, 1.75, 1.34" är inte det lite höga värden?
Någon som har använt Ubuntu ett längre tag vet garanterat bättre.

[Hund]

Har du uppgraderat från 7.04 till 7.10? Det skulle kunna blivit fel där. Om det är det du gjort kan du installera om allting. Vilket borde lösa problemet.